background image

Pro 1500 / 2000 © O.A.S. 2010

 15

XV. Fan Motor Maintenance

Wall Mounting Magnetic Starter

Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated 

every 5500 hours.

Per Baldor specifications, add .30 ounces (8.4 grams) 

of Mobil Polyrex grease by weight or .6 cubic inches 

(2 teaspoons) of Mobil polyrex grease by volume.

Fastener

Captive Fastener

Remove front cover.

Attach Starter cover and tighten Captive Fasteners.

Fasten screws through mounting bracket into 

mounting surface. (Screw needs to be smaller than 

Captive Fastener.)

Clean the grease fitting (or area around grease hole, if equipped with 

slotted grease screws). If motor has a purge plug, remove it> Motors 

can be re-greased while stopped (at less than 80 degrees C) or run-

ning. Apply grease gun to fitting (or grease hole). Too much grease 

or injecting grease too quickly can cause premature bearing failure. 

Slowly apply the recommended amount of grease, taking 1 minute or 

so to apply. Operate motor for 20 minutes, reinstall purge plug if previ-

ously removed. Caution: keep grease clean. Mixing dissimilar grease is 

not recommended.

Procedure

Содержание Pro 1500






















Отзывы: