background image

18

Combined  Super Gorilla Owner’s Manual © O.A.S. 2010

Bolt Together Stand

Replacement Filter

XVI. Accessories

STG000035 - 35 Gal. Stand
STG000055 - 55 Gal. Stand

FCS133695HF (2hp) / FCS183600HF (2.5/3/5hp)

18”x 36” / 110 Sq. Ft. - GE Certified (H-12) HEPA Media / MERV 16+ rated

w/ Pat. Pend. Flame Guard Arrestor

13”x 36” / 95 Sq. Ft. - GE Certified (H-12) HEPA Media / MERV 16+ rated

Dust Containers

35 Gal. Fiber

55 Gal. Fiber

55 Gal. Steel

The BAG Gripper

Drum Liner - 

Plastic Bag Hold-Down

ABX000000

ABX000035 / ABX000055

The BAG Gripper provides the ability to use convenient plastic bags inside your dust 

drum. It provides a Constant negative pressure on the outside surface of the plastic bag 

that keeps it pulled tight against the sides of the dust drum. Can be used with 35 and 55 

gal. barrels. Must be wired into your system.

Liner makes for easy empty and 

easy disposal of your waste.

TM

Filter Efficiency Gauge

FXK000000

This easy to read gauge takes the guesswork out of knowing when 

your filters need to be cleaned and tells you how much pressure 

is backed up behind your filters. It reads pressure from plenum to 

gauge up to 8’ away and allows you to keep your dust collection 

system running efficiently.

Dust Sentry™

AXB999110

Pat. Pending

 The Oneida Dust Sentry™ with adjustable IST (Infrared Sensing Technology), flashes a 

strobe light to alert you when the dust in your container reaches your preset level, telling 

you when it’s time to empty the container.

Содержание Dust Gorilla Pro Smart Boost XGK050105H























Отзывы: