background image

Oneida Air Systems

2

System Start-Up Information

1.  Do not vacuum anything that is burning or smoking, such as cigarettes, 

matches, hot ashes, or any hot substance!

2. 

Do not vacuum (or use this cyclone near) flammable or combustible 

liquids, gases, or explosive dusts, such as gasoline or other fuels, 

lighter fluid, cleaners, oil-based paints, natural gas, hydrogen, coal dust, 

magnesium dust, grain dust, aluminum dust, sugar dust, flour dust or 

gun powder.

3.  To reduce the risk of health hazards from vapors or dusts, do not 

vacuum toxic materials unless a HEPA filter is used. Do not use or store 

near hazardous materials.

4. 

Dust can be flammable and explosive. Some dust can be toxic or cause 

allergic reactions. 

5. 

Wood dust mixtures are highly flammable and can be explosive. 

NEVER introduce sparks or sources of ignition into collector.

a.  Empty drum after each use.
b.  Ground system. 

6.  NEVER leave wood dust in a building or vehicle.
7. 

Keep fire extinguishers handy at all times. 

8. 

Can be used for collecting non-flammable liquids. 

9. 

Dispose of waste in a FIRE SAFE AREA.

 

Ÿ

READ THE SAFETY PRACTICES INSTALLATION 
AND MAINTENANCE INSTRUCTIONS AND YOUR 
WET/ DRY VACUUM’S OWNER’S MANUAL BEFORE 
ASSEMBLING AND USING THE DUST DEPUTY

 

Ÿ

SOME DUSTS ARE HIGHLY FLAMMABLE OR 
EXPLOSIVE.  LEARN/ KNOW WHAT YOU ARE 
DEALING WITH. FOLLOW ALL LOCAL, STATE, 
FEDERAL & NFPA CODES AND GUIDE LINES.

Содержание Dust Deputy AXD001004





















Отзывы: