background image

10

Dust Cobra Owner’s Manual     O.A.S. 2010

c

 

 

VII. Filter Maintenance & Cleaning

Filter Cartridge Cleaning Intervals

Optional Cleaning Procedure

Caution! Fine dust collected in filter is hazardous to your health! Do not breathe!

Filters are easily cleaned by removing, placing inside a plastic bag and lightly tapping on floor. 

Dirt and debris will fall away from the filter. Wear dust mask when cleaning filter. For more thor-

ough cleaning, use the following steps.

1. Remove Filter from system and clean using compressed air (90 psi max.), blow the loose surface dust off of the filter, 

blowing from the outside / in to prevent forcing the dust into the media pores. Keep nozzle 6 - 8” from surface.

Do not use this method when any hazardous material has been vacuumed up.

2. After cleaning, inspect Filter for damage. Do not re-use a filter with bad gaskets, dented metal parts, torn media, etc...

1. Rinse the filter with a water hose (40 psi max.) on the outside. Wash from outside. Avoid getting water on the inside of 

filter. Do not use high pressure  nozzle or a power washer on inside of filter. The PTFE membrane surface on the inside of 

the filter is fragile and can be damaged.

2. Blow excess water off using compressed air (50 psi). Keep nozzle 6 - 8” away

    from inside surface to avoid damaging membrane.

3. Dry filters prior to returning them to service. It is NOT recommended to dry at

    temperatures above 150 Deg. F. 

The filter must be absolutely dry before re-use.

    Allow at least 24 hours of drying time.

4. Protect the filter from dust during the drying process.

5. Re-install the filter and run the collector 10 - 15 minutes without collecting any dust.

    Assure that all moisture is gone and there are no leaks prior to continuing service.

 

2. Sharply push bar down and 

hold for 5 seconds then 

release. Repeat this “popping” 

a few times.

3. Pull gate back down to

 

open suction to hose.

Frequent pulse cleaning of

 

the filter will keep vacuum

 

performance optimal.

If air flow is not restored,

 

check for clogs and clean 

filter.

Check to make sure filter is

 

in good condition with no 

cracks or tears or interrup-

tions in the seal.

When you replace filter,

make sure you tighten filter 

only enough to make a 

secure seal. If you over

tighten your filter you can 

break it.

A broken filter can leak 

material into the motor 

and cause severe 

damage!

You cannot operate the 

Dust Cobra without a  

proper filter in place. This 

can also cause severe 

damage to the motor and 

will void warranty!

How to Use the Filter Pulse Cleaning Bar

Warning! Do NOT shut off air to inlet for 

extended periods of time. This can cause 

motor to overheat and shut off!

1. Loosen knob. Push blastgate 

plate up to close off hose and 

tighten knob to hold.

Содержание Dust Cobra - XCK010000
















Отзывы: