background image

8

9

7.8. Test for communication function

   

Set and test it according to the communication function of the software of 

the upper monitor.

8.1. Outline of the menu.

1) LED display means the3 digital tube on control Panel from left to right.

2)  4  buttons  are  in  too  line.  There  is  only  the  SET  button  on  the  first  line. 
There are INC, STOP, DEC, SET buttons on the second line from up to down. 
SET  button  is  for  entering  or  exiting  the  menu.  INC  button  is  for  increasing 
the parameter. DEC button is for decreasing the parameter. STOP button is for 
keep  the  parameter  after  exiting  equipment.  If  user  needs  to  return  to  the 
setting status, press SET button.

8.2. setting to enter or exit the menu.

1) normal working mode. When the turnstile works, P00 appears on the LED 
display.  When  the  user  faces  the  turnstile  and  adjust  the  function  for  the 
turnstile  and  there  is  no  need  to  read  the  card,  press  INC  button.  The  boom 
will turn 20 degrees in the left direction. Press SET button, then the boom will 
turn 20 degrees in the right direction.

2)  When  turnstile  works  normally,  press  SET  button  to  enter  the  setting  of 
menu. P10 appears on the LED display. Press SET button again, P20 appears 
on the LED display, Continue to press SET button, P30 appears. It works the 
same way as other “ PXX ” till it reaches “000”. Then it exit the setting of the 
menu.
3) 15 functions for setting on the menu.
P10:semi-automatic  (  it  is  not  opened  normally.  It  can  be  opened  according 
to the clients' needs )
P11:full-automatical
P20:on-line mode
P21 off-line mode
P22: for testing the card-reading and unlocking the turnstile
P30: speed of the motor ( slow )
P31:speed of the motor(middle)
P32:speed of the motor ( fast )

Attention: there are no the three P30-P32 functions on this turnstile.

P40: time for unlocking and then locking ( short )
P41: time for unlocking and then locking ( middle )
P42: time for unlocking and then locking ( long )
P50: time for unlocking and then locking jamming (long )
P51: time for jamming ( long )
P52: time for jamming ( long ) 
P60: data canceling left machine ( press INC button )
P60: data canceling right machine ( press DEC button )
P70: Left can read the card , while right can be forbidden to pass
P71: Right can read the card , while left can be forbidden to pass
P72: Bi-directional forbidden pass
P73: Bi-directional card reading and staff limiting

     

4) Exit the setting of the menu: continue to press SET button for a cycle time. 
Then “ 000 ” appears, or press STOP button exit the menu design.

8.3. Setting function instruction

  

1) Enter into menu, press "set" key, after hear "dip", loose "set" key, and the 
screen display "P10" means already in the menu setting status, Either press 
"INC"  key  or  "DEC"  key  are  all  only  can  change  the  present  setting  status 
function.  In  the  status  of  no  card  reader,  the  arm  does  not  run.  Press  "INC" 
key, the screen display "P11" , and press "SET" key, the press display "P10" , 
If need to save the setting, press "SET" key, until the screen display "000" , 
which means the setting has been saved and exit the setting.
2)  Under  the  normal  working  status,  press  twice  "SET"  key,  enter  into  the 
working model setting, the screen display "P20" , either press "INC" key or 
"DEC" key are all only can change the present setting status function. In the 
status  of  no  card  reader,  the  arm  does  not  run.  Press  "INC"  key,  the  screen 
display  "P21",  and  press  "DEC"  key,  the  screen  display  "P20".  If  need  to 
save the setting, press "SET" key, until the screen display "000", which

8.  Instruction  for  adjusting  the  function  for  setting   

the menu.

3)  when  the  card  is  read  in  the  left:  when  the  card  is  read  in  the  left,  the 
turnstile will self-unlock automatically. The transit direction indication will 
turn to the green light. After the person transit and the booms rotate for 120 
degrees  Then  the  photo  electricity  restoring  switch  will  respond  to  it  and 
turn.  Then  the  motor  will  be  started  and  lock  the  turnstile.  The  transit 
indication will turn to the red light and the calculate will count the flow rate. 
It works the same way in the right!
The  longest  time  for  the  transit  is  10  seconds(  this  regulated  time  can  be 
fixed  by  the  user,  the  following  regulated  time  is  supposed  as  10  seconds.) 
When the regulated is over and no one transit, then the turnstile will restore 
and no number will be counted into the flow rate.

4)  Lower  the  boom  when  electricity  is  cut  off. When  the  turnstile  run  right 
and  suddenly  the  electricity  is  cut  off.  Then  the  turnstile  will  lower  the 
booms and permits the transit

7.7. Restoring function

      When the card is read effectively, the boom will rotate for 15 degrees and 
stop.  Then  the  transit  direction  indication  will  turn  to  the  green  light  and 
permits  transit. The  system  will  restore  and  cancel  the  transit  right  for  this 
time after the regulated time. And no number will be counted into
the flow rate.

Attention:  when  restoring,  the  rotating  booms  in  the  left  and  the  right 
should be even.

Содержание 2B-QDIS112









Отзывы: