background image

10-1

10. Reconfiguring Voltage and Frequency

“AS MANUFACTURED” BLOCK ON

NAMEPLATE

The genset was set up and adjusted at the factory

for the frequency and voltage stated in the “As

Manufactured” block on the nameplate (Fig-

ure 10-1). If it is necessary to reconfigure voltage

and/or frequency for the application, follow the in-

structions in this section.

RECONNECTION LABEL

The bag in which this manual was shipped has a

sheet with peel-off reconnection labels (Fig-

ure 10-2) to apply over the “As Manufactured” block

on the genset nameplate (Figure 10-1) when recon-

figuring the genset for the application. Apply the ap-

propriate label if different from the “As Manufac-

tured” data block.

CHANGING FREQUENCY

The genset control box has three frequency selec-

tion jumper leads terminated in connectors 

J5

P6

and 

P7

 (p. A-1). If application frequency is different

from “As Manufactured” frequency:

Connect 

J5

 to

 P6

 for 60 HZ.

Disconnect 

J5

 from

 P7

 for 50 HZ.

Apply the appropriate reconfiguration label.

RECONNECTING GENERATOR

WARNING

 Accidental or remote starting can

cause severe personal injury or death. Before

removing a panel or access door, disconnect

the negative (–) cable at the battery to prevent

the engine from starting.

Reconnect the generator for the application voltage,

if necessary, in accordance with the appropriate

generator connection schematic on Page A-2. Ap-

ply the appropriate reconfiguration label and adjust

voltage, if necessary. See ADJUSTING VOLTAGE

(p. 10-2).

Note: It may be necessary to change circuit breakers

to provide required protection or full genset power

when reconnecting the generator.

FIGURE 10-1. “AS MANUFACTURED” BLOCK ON

NAMEPLATE

FIGURE 10-2. RECONNECTION LABELS

Redistribution or publication of this document, 

by any means, is strictly prohibited.

Содержание MDKBH Series



























































































Отзывы: