© OMRON Corporation
2003
All Rights Reserved.
PRECAUTION FOR SAFE USE
To use the Controller safely and at full capacity, be sure to read the
Handling Instruction Manual carefully. You are requested to fully
understand this system.
(1)Environment
Do not expose V690-HMG01 to explosive gas, inflammable gas,
corrosive gas, metallic powder, dust particlesetc, etc.
(2)Water-tight
This product is not water-tight.
V690-HMG01 may malfunction, suffer damage, or burn, in
places where they may be exposed to water, oil, medicines, or
organic solvent.
(3)Enclosure of the product
Do not remove the casing of this product. Otherwise, the
product may malfunction forever.
■
Specifications
●
General specification
●
Indicator
●
Performance specifications
Power supply
Ambient temperature
Ambient humidity
Specifications
24V DC
＋
10% /
−
15%
−
20 to
＋
60
℃
（
with no icing
）
35 to 85%
（
with no condensation
）
Item
Transmission Frequency
2434.25
〜
2465.75MHz
Emission power
10mW
ID System Read/Write Antenna
Model
V690-HMG01A
2
3
4
C
H
T
Red
Yellow
Green
1
Name
P
Meaning
Green
No
Specification
Item
Vibration resistance
Enclosure rating
Setup method
Weight
Durable at 10 to 150Hz
Double amplitude less than 0.7mm
10 sweeps for 8 minutes each in 3 directions.
IP62
(when placing the connector side down)
Mounting on DIN rail or fixed with M5 screws
About 2.6Kg
Shock resistance
150m/s
2
, 3 times in 6 directions
Cable length
0.5m with a watertight connector
Dielectric strength
1000V AC 50/60Hz for 1 min
Between cable terminals and case
Insulation resistance
20 M
Ω
min. (at 100V DC )
Between cable terminals and case
■
Dimensions
Remains lit when the power is turned on
Lit when the antenna sends an elec tromagnetic wave
Lit when the antenna sends the data to a Host computer
Lit when the antenna sends the data to a tag
Applied standards
R&TTE / FCC Part15 Subpart C
PRECAUTION FOR CORRECT USE
(1)Do not use it in the following environment.
Places where the temperature varies heavily.
Places where the humidity is high and it condenses.
Where the antenna may get splashed with water, oil, chemicals
or organic solvents.
Where the antenna is exposed to corrosive gases.
Where a noise-generating source is nearby.
(2) Installation
Avoid setting up the unit near a highly heat-generating device
(such as heater, transformer and large-capacity resistor).
Tighten the M5 mounting screws to a smaller torque than 2.3
N
・
m. Do not apply screw loctite and any other organic solvent
to any other parts than the screws. The casing may get cracked.
(3)Cleaning
Be sure to use the market alcohol and benzene.
Do not use the thinner.
(4)Be sure to connect the grounding.
If the grounding is not connected, the read/write antenna may fail
to function.
260.3
280
260.3
280
260.3
40
28
MOUNTING SCREW HOLES
28
19
24
INDICATORS
CONNECTOR
BUSH
VINYL INSULATED ROUND CORD 7.5dia.
12 CORES LENGTH 0.5M
21
260.3
4-M5
4-6dia.
MOUNTING HOLES
20dia.
23dia.
60
FERRITE CORE
OMRON Corporation
Suitability for Use
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A
Phone:1-847-843-7900 Telephone Consultation
1-800-55-OMRON Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE LTD
83 Clemenceau Avenue,#11-01 UE Square,Singapore 239920
Phone : 65-6-835-3011 /Fax :65-6-835-2711
n
THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED.
THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the
systems, machines, and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
LAWS AND STANDARDS
1
．
United States
FCC Part15 Subpart C
FCC ID: E4E6CYCIDV6900101
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
・
Select only with "Low Power Mode(2m mode).
（
Default Setting is "Low(2m mode)."
The use of "High power mode (5m mode)" is not allowed
by FCC.
whose rule has penalty clause.
2. Europe
EC/R&TTE Directive
（
Radio and Telecommunication
Terminal Equipment Directive 1999/5/EC
）
The V690 is allowed to use:
Austria, Belgium, Denmark, Finland, France, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands,
Norway, Spain, Switzerland, UK.
・
Select only radio wave channel"5". Do not use theV690 in the
other channels.
（
Default Setting is "5."
）
To use V690 in channels except channel 5 is not allowed by
Radio lows of each country, which may have penalty clause.
3. For the use in other countries
Please contact our sales representatives.
Color
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
