manualshive.com logo in svg

Omron SYSMAC NY Series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron SYSMAC NY Series Скачать руководство пользователя страница 185

7-2-5

Replace a Drive

Use the following procedure to replace a drive.

Prepare the new drive.

Additional Information

• Refer to 

1-4 Product Configuration Box PC

 on page 1-5 for the installed drive model.

• Refer to 

3-10-5 HDD and SSD Storage Devices

 on page 3-25 for the available drive models.

• Refer to 

4-1-7 Storage Device Specifications

 on page 4-11 for drive specifications.

To replace a drive:

1

Power OFF the Box PC.

2

Remove the drive cover.

1

3

2

1) Push the lock lever 

1

.

2) Tilt the cover 

2

.

3) Remove the drive cover 

3

.

Additional Information

• Refer to 

3-7 Drive Bays

 on page 3-18 for the location of the drive cover.

• The Box PC has 2 drive bays, marked with "A" and "B" at the left side of the drive cover. Take

note of the bay position for the drive that is being removed and do not place a drive in the
incorrect bay.

7 Maintenance

7-11

NY-series Industrial Box PC Hardware User's Manual (W553)

7-2
 Corrective Maintenance

7

7-2-5

 Replace a Drive

Содержание SYSMAC NY Series





































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды