Omron SYSMAC C200H-AD003 Скачать руководство пользователя страница 18

Страница: 18 / 145

1-2

Section

Basic Configuration

Mounting Analog I/O Units

Use the following procedure to mount an Analog I/O Unit to the Backplane.

1, 2, 3...

1. Lock the top of the Analog I/O Unit into the slot on the Backplane and rotate

the Unit downwards as shown in the following diagram.

Hook

Backplane

Lock lever

2. While making sure to align the Unit properly with the connectors, press

down on the lock lever at the bottom of the slot, press the Unit firmly into po-
sition, and then release the lock lever.

(To remove a Unit, hold down the lock lever with an implement such as a
screwdriver.)

Lock lever

Leave enough space below each Rack, as shown in the following diagram for
mounting and removing the Units.

20 mm min.

Backplane

Flat-blade screwdriver

Precautions

Be sure to turn off the power supply to the PC before installing or disconnecting
Units or connecting lines.

To reduce the risk of malfunctioning due to electrical noise, wire input and output
lines in separate ducts from high-voltage and power lines.

Содержание SYSMAC C200H-AD003


















































































































































Результаты поиска

Содержание SYSMAC C200H-AD003

Отзывы:

Бренды по названию

Популярные бренды

Omron SYSMAC C200H-AD003, Руководство по эксплуатации

Результаты поиска

Содержание SYSMAC C200H-AD003

Отзывы:

Бренды по названию

Популярные бренды