Omron PRT1-SCU11 Скачать руководство пользователя

Страница: 24 / 78

PROFIBUS-DP Gateway Unit

Section 1-3

Protocol Specifications

Item

Specification

Host

nk /

Com

-F

ace

Protocol type supported

Host Link or Compoway-F

Host Link media type

RS-422, galvanically isolated.
Selection for RS-422 is made with Physical layer switch 1(see

2-1-3

Switch Settings).

OFF: RS-422 (for device type R88A-MCW151-E)

Compoway-F media type

RS-485, galvanically isolated.
Selection for RS-485 is made with Physical layer switch 1(see

2-1-3

Switch Settings).

ON: RS-485 (for device type, E5ZN, E5_R and E5_N)

RS-232C interface

Use the CS1W-CN226 connection cable for connecting the Gateway
with Thermotools

RS-485 or RS-422 termination resistor

Internal 220 Ohm resistor between receiver lines.
Use of resistor can be enabled or disabled, using Physical layer switch
2.

Host Link / Compoway-F connector

5-pin Phoenix connector

Device address range

~ 15, set through the slot number of the PROFIBUS module configu-

ration. Number 0 (zero) is reserved.

Baud rates supported, selection with
DIP-switches 1 and 2. (See

2-1-3 Switch

Settings)

• 9.6 kbit/s
• 19.2 kbit/s
• 38.4 kbit/s

OFI

US-

P i

ace

Applicable standards

EN50170, Volume 2

Protocol type supported

PROFIBUS-DP

PROFIBUS Unit type

PROFIBUS-DP slave

PROFIBUS Media type

RS-485, galvanically isolated

PROFIBUS Connector

9-pin sub-D female connector (#4/40 UNC thread)
Termination according to EN50170 provided by the cable connector

Unit device address range

~ 99, set through rotary switches

Remote setting not supported.

Baud rates supported (Auto-detect)

• 9.6 kbit/s
• 19.2 kbit/s
• 45.45 kbit/s
• 93.75 kbit/s
• 187 kbit/s
• 500 kbit/s
• 1.5 Mbit/s
• 3 Mbit/s
• 6 Mbit/s
• 12 Mbit/s

PROFIBUS services supported

• Set_Prm
• Chk_Cfg
• Get_Cfg
• Slave_Diag
• Data_Exchange
• RD_Inp
• RD_Outp
• Global_Control - Sync / Unsync Freeze / Unfreeze/ Clear

Number of I/O data supported

Up to 200 bytes input and 200 bytes output max.

Number of diagnostics data supported

6 Bytes basic, and 7 bytes extended.

Содержание PRT1-SCU11















































































Результаты поиска

Содержание PRT1-SCU11

Отзывы:

Похожие инструкции для PRT1-SCU11

Бренды по названию

Популярные бренды

Omron PRT1-SCU11, Руководство по эксплуатации

Результаты поиска

Содержание PRT1-SCU11

Отзывы:

Похожие инструкции для PRT1-SCU11

Бренды по названию

Популярные бренды