Omron PRT1-SCU11 Скачать руководство пользователя | Manualshive

Страница: 11 / 78

background image

xiv

Application Precautions

5

• When adding a new Host Link or Compoway-F node to the network, make

sure that the PROFIBUS-DP Gateway to Host Link/Compoway-F is pow-
ered down, to prevent unexpected results when starting up the new node.

• Use specified communications cables.

• Do not extend connection distances beyond the ranges given in the spec-

ifications.

• Always turn OFF the power supply to the personal computer, Slaves, and

Communications Units before attempting any of the following.

• Mounting or dismounting the PROFIBUS-DP Gateway to Host Link/

Compoway-F, Power Supply Units, I/O Units, CPU Units, or any other
Units.

• Assembling a Unit.

• Setting DIP-switches or rotary switches.

• Connecting or wiring the cables.

• Connecting or disconnecting connectors.

• Be sure that all the mounting screws, terminal screws, Unit mounting

screws, and cable connector screws are tightened to the torque specified
in the relevant manuals. Incorrect tightening torque may result in malfunc-
tion.

• Leave the label attached to the Unit when wiring. Removing the label may

result in malfunction if foreign matter enters the Unit.

• Remove the label after the completion of wiring to ensure proper heat dis-

sipation. Leaving the label attached may result in malfunction.

• Always use the power supply voltage specified in this manual.

• Double-check all the wiring and connection of terminal blocks and con-

nectors before mounting the Units.

• Use crimp terminals for wiring. Do not connect bare stranded wires

directly to terminals.

• Observe the following precautions when wiring the communications

cable.

• Separate the communications cables from the power lines or high-ten-

sion lines.

• Do not bend the communications cables.

• Do not pull on the communications cables.

• Do not place heavy objects on top of the communications cables.

• Be sure to wire communications cable inside ducts.

• Use appropriate communications cables.

• Take appropriate measures to ensure that the specified power with the

rated voltage and frequency is supplied in places where the power supply
is unstable. An incorrect power supply may result in malfunction.

• Install external breakers and take other safety measures against short-cir-

cuits in external wiring. Insufficient safety measures against short-circuits
may result in burning.

• Double-check all the wiring and switch settings before turning ON the

power supply.

• When transporting or storing the product, cover the PCB’s with electrically

conductive materials to prevent LSI’s and IC’s from being damaged by
static electricity, and also keep the product within the specified storage
temperature range.

«
...
9
10
11
12
13
...
»

Содержание PRT1-SCU11















































































Отзывы:

Нет отзывов

Похожие инструкции для PRT1-SCU11

Бренд: Ubisys Страницы: 51

Бренд: Karel Страницы: 17

Бренд: Panasonic Страницы: 72

Бренд: PAC Страницы: 20

Sentrius RG1 Series

Бренд: Laird Страницы: 27

WAGO 750-8212/000-100

Бренд: Viessmann Страницы: 36

Бренд: BAB TECHNOLOGIE Страницы: 52

Бренд: Ubiquiti Страницы: 19

Бренд: DAUDIN Страницы: 24

Бренд: Qiagen Страницы: 22

M2M CONTROL C660

Бренд: Infranet Technologies Страницы: 36

NEXEDGE NX-700 series

Бренд: Kenwood Страницы: 3

Бренд: IFM Electronic Страницы: 65

Бренд: IFM Страницы: 28

Бренд: IFM Страницы: 85

Бренд: 4IPNET Страницы: 24

CODA-4 8 Series

Бренд: Hitron Страницы: 150

Бренд: enphase Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды