Example:
Unit version of CPU Unit: 1.14
Sysmac Studio version: 1.17
The unit version of the CPU Unit that corresponds to Sysmac Studio version 1.17 is unit version
1.13.
Therefore, you can use only the functions that are supported by a CPU Unit with a unit version
of 1.13.
You cannot use functionality that was added for unit version 1.14 or later of the CPU Unit.
l
Using a CPU Unit with an Earlier Unit Version
If you use an NX-series CPU Unit with an earlier version, select the unit version of the used CPU
Unit or an earlier unit version in the Select Device Area of the Project Properties Dialog Box on the
Sysmac Studio. The unit version that you selected is the project unit version of the project. You can
use only the functions that are supported by the project unit version.
Example:
Unit version of CPU Unit: 1.14
Sysmac Studio version: 1.20
Unit version 1.16 of the CPU Unit corresponds to Sysmac Studio version 1.20.
However, the used CPU Unit is unit version 1.14, so select
version 1.14
or earlier as
version
in
the Select Device Area of the Project Properties Dialog Box.
If you select
version 1.14
as the
version
in the Select Device Area of the Project Properties Dia-
log Box, you can use only the functions that are supported by project unit version 1.14. You can-
not use functionality that was added for unit version 1.16 or later of the CPU Unit.
Additional Information
Project Unit Version for Projects
• With Sysmac Studio version 1.02 or higher, you can select the unit version in the Select De-
vice Area of the relevant dialog boxes.
• You can select any unit version that is the same as or earlier than the unit version of the CPU
Unit. For example, if the unit version of the CPU Unit is 1.14, select either
1.13
or
1.14
.
• The Sysmac Studio will treat the project unit version as the unit version of the CPU Unit. For
example, if the project unit version is 1.13, you can use the functionality for unit version 1.13
on the Sysmac Studio.
• You can transfer a project to the Sysmac Studio if the project unit version is the same as or
earlier than the unit version of the destination CPU Unit.
• Refer to the
Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-03 or later)
for
details on the Select Device Area of the relevant dialog boxes.
A-3-2
Functions That Were Added or Changed for Each Unit Version
This section describes the functions that were added or changed for each unit version of NX-series
NX1P2 CPU Unit.
l
Additions and Changes to Functional Specifications
The following table gives the unit version of the CPU Units and the Sysmac Studio version for each
addition or change to the functional specifications.
Appendices
A-7
NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)
A-3
V
ersion Information
A
A-3-2 Functions That W
ere Added or Changed for Each Unit V
ersion
Содержание NX1P2 series
