![background image](http://html1.mh-extra.com/html/omron/ne1a-scpu01-07-2009/ne1a-scpu01-07-2009_operation-manual_742749238.webp)
203
Indicator/Display Status and Corrective Actions for Errors
Section 10-3
Flashing
red
L9
"
Master node
address
---
Standard I/O
Connection
Timeout
See note
1.
Standard I/O
connection
timeout
Check the following points:
• Make sure the baud rate is the
same for all nodes.
• Make sure the cable lengths
(main/branch) are not too
long.
• Make sure the cable is not dis-
connected or loose.
• Make sure terminating resis-
tance is at both ends of the
main line and only at both
ends.
• Make sure that there is not a
lot of noise.
Flashing
red
dA
Ù
Desti-
nation slave
node
address
---
Safety I/O
Connection
Timeout
See note
1.
Safety I/O
connection
timeout
Flashing
red
d5
Ù
Desti-
nation slave
node
address
---
Nonexistent Slave
Device
See note
1.
No slave
Flashing
red
d6
Ù
Desti-
nation slave
node
address
---
Safety I/O
Connection
Establishment Fail-
ure
See note
1.
Safety I/O con-
nection establish-
ment error
Check the slave device.
• Make sure it its configured.
• Make sure it is in a normal
operational state.
Flashing
red
d6
Ù
Desti-
nation slave
node
address
---
Invalid Slave
Device
See note
1.
Invalid slave
device (verifica-
tion error)
Verify the slave device (select
Device - Parameters - Com-
pare
) and connect a suitable
slave device.
OFF
E0
Ù
Node
address of
error
---
Network PS
Voltage Low
See note
1.
Network power
supply voltage
low error
Check the following points:
• Make sure the power supply
voltage is set within the speci-
fied range.
• Make sure a cable or wire is
not disconnected.
---
E2
Ù
Node
address of
error
---
Transmission
Timeout
See note
1.
Transmission
timeout
Check the following points:
• Make sure the baud rate is the
same for all nodes.
• Make sure the cable lengths
(main/branch) are not too
long.
• Make sure the cable is not dis-
connected or loose.
• Make sure terminating resis-
tance is at both ends of the
main line and only at both
ends.
• Make sure that there is not a
lot of noise.
Flashing
red
A0
Ù
Node
address of
error
---
Relevant Safety I/O
communication
stopped because of
a Safety I/O
communication
error
Yes
(See note
2.)
A safety I/O
connection timed
out, interrupting
the relevant I/O
connection.
Check the following points:
• Make sure the baud rate is the
same for all nodes.
• Make sure the cable lengths
(main/branch) are not too
long.
• Make sure the cable is not dis-
connected or loose.
• Make sure terminating resis-
tance is at both ends of the
main line and only at both
ends.
• Make sure that there is not a
lot of noise.
Flashing
red
A1
Ù
Node
address of
error
---
All Safety I/O
com-munication
stopped because
ofa Safety I/O
communication
error
Yes
(See note
2.)
A safety I/O
connection timed
out, interrupting
the relevant I/O
connection.
Indicators/display
Error history
Cause
Corrective actions
NS
Seven-
segment
display
I/O
Name
Saved in
nonvola-
tile
memory
Содержание NE1A-SCPU01 - 07-2009
