manualshive.com logo in svg

Omron H8PS, Руководство пользователя

Поделиться
Скачать
Omron H8PS Скачать руководство пользователя страница 27

Cam Positioner

 H8PS

27

Advance Angle Compensation (ADV) 
Function

The advance angle compensation function automatically advances 
the ON/OFF angle of cam outputs in proportion to machine 
(encoder) speed. As the speed of the machine increases, the system 
can be affected by the delay in outputs. If the ADV function is used, 
the output delay caused by higher speeds is automatically 
compensated. 

As shown in the following diagram, ADV function is used to linearly 
compensate outputs according to the speed based on the ADV value 
setting for a specific speed. 

Example: ADV Value Set to 2

°

 at 100 r/min 

ADV value can be set independently for cams 1 to 7 (7 total). For the 
ADV function, the speed and the amount of angle compensation are 
set. If “- - -” is displayed for any setting, the ADV function is disabled. 

The setting ranges are given in the following table. 

Note:

Default settings are shown in reverse type. 

The maximum response speed will decrease as shown in the 
following table when ADV values are set for 4 cams or more. 

Note:

Even if the ADV value is set to 0°, the cam must be included in 
the number of cams with ADV settings. 

1.

Set the mode switch to PRGM or TEST. 

2.

Set cam number 4 with the CAM Keys 

. (See note.) 

3.

Press the 

 Key to move to the ADV function setting display

and confirm that "ADV" is displayed. 

Setting Display

7.

Press the 

 Key after finishing setting the ADV function. The

previous display in Programming or Test Mode will be resumed. 

Note:

If the bank function is being used, set the bank number before 
setting the cam number. 

Encoder Speed

ADV 

value

Resolution Display angle

256

256

“ 

- - -

 ”, 1 to 1,600

“ 

- - -

 ”, 0 to 255

256

360

“ 

- - -

 ”, 1 to 1,600

“ 

- - -

 ”, 0 to 359

360

---

“ 

- - -

 ”, 1 to 1,600

“ 

- - -

 ”, 0 to 359

720

---

“ 

- - -

 ”, 1 to 800

“ 

- - -

 ”, 0 to 359.5

Number of cams 

with ADV settings

Encoder resolution

Max. response 

speed

0 to 3

256/360

1,600r/min

720

800r/min

4 to 7

256/360

1,200r/min

720

600r/min

Amount of angle compensation

100

0

Speed (r/min)

Note

: The maximum amount of angle compensation is 360

°

.

ADV value

2

°

100

°

8

°

 advance angle  

compensation 

Cam program setting 

180

°

92

°

172

°

At high speed
(400r/min)

Example: Setting the ADV Value to 2

°

 at 100 r/min for Cam 4

4.

Set the speed to 100 with the 
ANGLE Keys 

 and then 

press the 

 Key. 

5.

Set the ADV value to 2 with the 
ANGLE Keys 

. 

6.

Press the 

 Key to write 

the settings to memory.

ADV

CAM

STEP

TST

WRITE

TST

CAM

STEP

TST

CAM

STEP

WRITE

ADV

Содержание H8PS

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды