Omron GigE Vision STC-CMB2MPOE Скачать руководство пользователя страница 14

Страница: 14 / 55

No.13S064-13

14/55

STC-CMC2MPOE / STC-CMB2MPOE / STC-CMB2MPOE-IR /
STC-CMC4MPOE / STC-CMB4MPOE / STC-CMB4MPOE-IR Product Specifications and User’s Guide

4.3

Mechanical Specifications

Model Number

STC-CMB2MPOE / STC-CMB4MPOE /

STC-CMB2MPOE-IR / STC-CMB4MPOE-IR

STC-CMC2MPOE / STC-CMC4MPOE

Dimensions

35 (W) x 35 (H) x 55.9 (D) mm (*1)

Optical Filter

No Optical Filter

No Optical Filter (*2)

Optical Center Accuracy

Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm

Rotational accuracy of Horizontal and Vertical: +/- 2.0 deg.

Material

Aluminum (AC)

Lens Mount

C mount

Connectors

RJ45 connector

Power- I/O connector: HR10A-7R-6PB (Hirose) or equivalent

Camera Mount Screws

Two 1/4” Tripod screw holes (One on top and bottom plate)

Eight M4 screws holes (Four on top and bottom plate)

Weight

Approximately 120 g

(*1) Excluding connectors
(*2) The color model with IR Cut Filter is optional mode. Please contact to sale representative.

4.4

Environmental Specifications

Model Number

STC-CMB2MPOE / STC-CMB4MPOE /

STC-CMB2MPOE-IR / STC-CMB4MPOE-IR

STC-CMC2MPOE / STC-CMC4MPOE

Operational

Temperature / Humidity

Minimum

Environmental Temperature -5 deg. C,

Environmental Humidity: 0 to 85 %RH (No condensation)

Maximum (*1)

Camera housing temperature (top plate) shall not 65 deg. C

(This corresponds to an environmental temperature of approxi40 deg. C)

Storage Temperature / Humidity

Environmental Temperature: -30 to +65 deg. C,

Environmental Humidity: 0 to 85 %RH (No condensation)

Vibration

20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G, XYZ 3 directions 30 min. each)

Shock

Acceleration 38 G, half amplitude 6 mseconds, XYZ 3 directions 3 times each

Standard Compliancy

EMS: EN61000-6-2, EMI: EN55011

RoHS

RoHS Compliance

(*1) When the camera using under the condition that e40 deg. C environmental temperature, please insure the

camera installs with the appropriate heat dissipation to keep the housing temperature less than +65 deg. C.

If camera has a mounted lens and a tripod with an aluminum plate, this could decrease the camera housing

temperature for heat dissipation.

Taking these steps will maintain the heat rating of the electronic components of the camera.

Upper side of camera

Measuring point

Содержание GigE Vision STC-CMB2MPOE
























































Результаты поиска

Содержание GigE Vision STC-CMB2MPOE

Отзывы:

Похожие инструкции для GigE Vision STC-CMB2MPOE

Бренды по названию

Популярные бренды

Omron GigE Vision STC-CMB2MPOE, Технические характеристики и руководство пользователя

Результаты поиска

Содержание GigE Vision STC-CMB2MPOE

Отзывы:

Похожие инструкции для GigE Vision STC-CMB2MPOE

Бренды по названию

Популярные бренды