This product is not designed or rated for ensuring safety
of persons. Do not use it for such purposes.
Meaning of Alert Symbols
Alert statements
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
Model
FZ-SC/S
DIGITAL CAMERA FOR
VISUAL INSPECTION SYSTEM
General specifications
*The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is
polarized, so, make sure that the end bearing a name
plate is connected to the controller.
(1) The camera base attached to the bottom of the
camera can also be attached to the another side of
the camera,Remove the four screws(M2×7) from
the base and re-attach the base to the another side
of the camera.(Recommended screw tightening
torque
:
0.32N
・
m)
If you attach the camera base to the top or side of
the camera, attach with three screws.
The center of the optical axis varies with the camera used.
Therefore, when installing the camera, always check the
center of the image displayed on the monitor.
Item
Model
FZ-S
FZ-SC
Power
consumption
2.4W max.(12V DC , 0.2A max.)
Vibration
resistance
10 to 150Hz: half-amplitude: 0.35mm:
(maximum acceleration: 50m/s
2
),
10 times for 8 minutes each in 3 directions
Shock resistance
Shock resistance 150m/s
2
;
3 times each in 6 directions
Ambient
Temperature
Ambient
humidity
Operating and storage: 35% to 85%
(with no condensation)
Ambient
environment
Center positional
accuracy of
optical axis
No corrosive gases
X, Y :
±
0.31mm
∂
x,
∂
y :
±
2.1
°
Operating: 0 to 50
℃
(with no icing nor condensation)
Storage: -25 to 65
℃
(with no icing nor condensation)
Materials
Case (Front and Rear) : Aluminium
Camera mounting base : PC / ABS
Weight
Approx. 55g
(
including base
)
Degree of
protection
IEC60529 IP20 (in-panel)
Picture element
Effective pixels
Pixel size
Scanning method
Vertical frequency
Horizontal frequency
Pixel frequency
Number of lines
to be read
Synchronization
Video output
Gain
Shutter speed
Lens mounting
Item
Model
FZ-S
FZ-SC
WARNING
PRECAUTIONS ON SAFETY
1/3-inch interline CCD
(reading all pixels)
659(H)
×
494(V)
7.4(
μ
m)
×
7.4(
μ
m)(Square pixel)
Non-interlace mode
80.600Hz
39.336KHz
30.682MHz
12 lines to 480 lines
Internal Sync.
Digital (10 bits)
FZ-S : 0 dB to +20dB
FZ-SC : 0 dB to +13dB
1/10
to
1/50000s
C mount
・
In order to secure the safety of operation and
maintenance, set the product apart from high
voltage equipments and power instruments.
・
Make sure to tighten all installation screws
securely.
PRECAUTIONS FOR SAFE USE
・
Do not use unspecified camera cable and a strobe
controller other than those that specified in this
manual with the FZ controller. Connection with
unspecified camera cable and/or strobe controller
may cause temperature rise and malfunctions at the
worst case.
・
If you do not use the enhancing connector on the
back of the camera,do not remove the cap that is
attached to the connector.
Please observe the following precautions to prevent
failure to operate, malfunction, or undesirable effect.
・
Be sure to turn off the power before connecting or
disconnecting the cables.
The Camera's case is connected to the 0V line in the
internal circuits. Observe the following precautions to
prevent noise interference.
・
Do not ground the Camera.
・
Do not remove the base attached to the Camera.
PRECAUTIONS FOR CORRECT USE
(1)Installing circumstance
(2)Others
(1)Connecting Cables
(2)Handling the Camera
(3)Optical axis of the camera
・
Dirt on the CCD must be removed using an air brush.
・
Do not use thinners or benzene to clean the Controller.
(4)Maintenance
■
Specifications
Performance specifications
■
Changing the Camera Base Mount Position
(1) Using the Camera cable FZ-VS
□□
(sold
separately), connect the connector on the back of
the camera and the camera connector on Controller
FZ series.
■
Connecting
■
Dimensions
© OMRON Corporation 2006 All Rights Reserved.
Camera cable
FZ-VS
□□
Camera
FZ-SC/S
(
Unit
:
mm
)
Name plate
Enhancing connetor
Camera cable
connector
Be sure to respect following items for safety.
・
Do not attempt to dismantle, repair, or modify the
main body.
・
If you suspect an error or malfunction, stop using the
Controller immediately, turn OFF the power supply,
and consult your OMRON representative.
・
Dispose of FZ-SC components as industrial waste.
Indicates a potentially hazardous situation which, if
not avoided, will result in minor or moderate injury,
or may result in serious injury or death. Additionally
there may be significant property damage.
WARNING
NOTICE:
This product meets CISPR11 class A. The intended use of this product is in an
industrial environment only.
TRACEABILITY INFORMATION:
Representative in EU
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
Manufacturer
Omron Corporation,
Sensing Devices & Components Div.H.Q.,
Application Sensors Division
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 JAPAN
OMRON Corporation
Suitability for Use
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A.
Phone:1-847-843-7900 Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road #05-05-08(Lobby 2),
Alexandra Technopark, Singapore 119967
Phone : 65-6835-3011 Fax :65-6835-2711
o
THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED.
THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the
systems, machines, and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
CHINA
OMRON(CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Phone : 86-21-5037-2222 Fax :86-21-5037-2200
OCT, 2009
D
14.5
10.5
22
40
(7.3)
12
20.5
3-M2 DEPTH 3.0(BOTH SIDE)
12
14.5 22
3-M2 DEPTH 3.0
10.5
9.5 9.5
5.5
33.5
2-M4 DEPTH 5.5
1/4-20UNC DEPTH 5.5
6.5
28
28
24
1"-32UN-2A(C MOUNT)
(19.4)
(5.4)
(7.9)
FZ-S : monochrome
FZ-SC : color