Omron E5CK-AA1-500 AC100-240 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

Omron E5CK-AA1-500 AC100-240 Скачать руководство пользователя страница 19

E5CK-T

E5CK-T

187

J

LEVEL 1 MODE

AT Execute/Cancel

Proportional Band
Available if the Controller is in advanced PID control.

Integral Time
Available if the Controller is in advanced PID control.

Derivative Time
Available if the Controller is in advanced PID control.

For heating/cooling control

For models E5AK/EK-T only

Cooling Coefficient
Used with the Controller is in
heating and cooling control.

Dead Band
Used with the Controller is in
heating and cooling control.

Manual Reset Value
Available when the integral time parameter
of the Controller in standard control is “0.”

Hysteresis (Heat)
Available when the Controller is in
ON/OFF control.

For heating/cooling control

Hysteresis (Cool)
Available when the Controller is in
ON/OFF control.

Control Period (Heat)
Available when the Controller has a relay or
voltage output, or is in advanced PID control.

For heating/cooling control

Control Period (Cool)
Available when the Controller has a relay
or voltage output, or is in advanced PID
control.

Current value

Heater Current Monitor
Available when the heater burnout alarm is
assigned. For models E5AK-T/E5EK-T only.

Heater Burnout Detection
Available when the heater burnout alarm is
assigned. For models E5AK-T/E5EK-T only.

Position-
proportional
dead band

«
...
17
18
19
20
21
...
»

Содержание E5CK-AA1-500 AC100-240





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды