background image

E5CD-800/E5ED-800

41

Service Life

1.

Use the Digital Temperature Controller within the following 

temperature and humidity ranges:

Temperature: 

10 to 55°C (with no icing or condensation), 

Humidity: 25% to 85%

If the Digital Temperature Controller is installed inside a control 

board, the ambient temperature must be kept to under 55°C, 

including the temperature around the Digital Temperature 

Controller.

2.

The service life of electronic devices like Digital Temperature 
Controllers is determined not only by the number of times the relay 
is switched but also by the service life of internal electronic 
components. Component service life is affected by the ambient 
temperature: the higher the temperature, the shorter the service 
life and, the lower the temperature, the longer the service life. 
Therefore, the service life can be extended by lowering the 
temperature of the Digital Temperature Controller.

3.

When two or more Digital Temperature Controllers are mounted 
horizontally close to each other or vertically next to one another, 
the internal temperature will increase due to heat radiated by the 
Digital Temperature Controllers and the service life will decrease. 
In such a case, use forced cooling by fans or other means of air 
ventilation to cool down the Digital Temperature Controllers. When 
providing forced cooling, however, be careful not to cool down the 
terminals sections alone to avoid measurement errors.

Ensuring Measurement Accuracy

1.

When extending or connecting the thermocouple lead wire, be 

sure to use compensating wires that match the thermocouple 

types.

2.

When extending or connecting the lead wire of the platinum 
resistance thermometer, be sure to use wires that have low 
resistance and keep the resistance of the three lead wires the 
same.

3.

Mount the Digital Temperature Controller so that it is horizontally 
level.

4.

If the measurement accuracy is low, check to see if input shift has 
been set correctly.

Resistance to Water

The degree of protection is as shown below. Sections without any 
specification on their degree of protection or those with IP

0 are not 

waterproof.
Front panel: IP66
Rear case: IP20, Terminal section: IP00
When waterproofing is required, insert the Waterproof Packing on the 
backside of the front panel.
Keep the Port Cover on the front-panel Setup Tool port of the E5ED-
800 securely closed. The degree of protection when the Waterproof 
Packing is used is IP66. To maintain an IP66 degree of protection, the 
Waterproof Packing and the Port Cover for the front-panel Setup Tool 
port must be periodically replaced because they may deteriorate, 
shrink, or harden depending on the operating environment.
The replacement period will vary with the operating environment. 
Check the required period in the actual application. Use 3 years or 
sooner as a guideline. If the Waterproof Packing and Port Cover are 
not periodically replaced, waterproof performance may not be 
maintained.
If a waterproof structure is not required, then the Waterproof Packing 
does not need to be installed.

Precautions during Operation

1.

It takes approximately two seconds for the outputs to turn ON from 

after the power supply is turned ON. Design the system (e.g., 

control panel) to allow for this delay.

2.

Make sure that the Digital Temperature Controller has 30 minutes 
or more to warm up after turning ON the power before starting 
actual control operations to ensure the correct temperature 
display.

3.

Avoid using the Digital Temperature Controller in places near a 
radio, television set, or wireless installing. The Digital Temperature 
Controller may cause radio disturbance for these devices.

Mounting

E5CD-800

Mounting to the Panel

1.

For waterproof mounting, waterproof packing must be installed on 

the Digital Temperature Controller. Waterproofing is not possible 

when group mounting several Digital Temperature Controllers.

2.

Insert the E5CD-800 into the mounting hole in the panel.

3.

Push the Adapter from the terminals up to the panel, and 
temporarily fasten the E5CD-800.

4.

Tighten the two fastening screws on the Adapter. Alternately 
tighten the two screws little by little to maintain a balance. Tighten 
the screws to a torque of 0.29 to 0.39 N·m.

Mounting the Terminal Cover

There are two models of Terminal Covers that you can use with the 
E5CD-800.
Slightly bend the E53-COV23 Terminal Cover to attach it to the 
terminal block as shown in the following diagram. The Terminal Cover 
cannot be attached in the opposite direction. Or, you can use the E53-
COV17 Terminal Cover. Make sure that the “UP” mark is facing up, 
and then attach the E53-COV17 Terminal Cover to the holes on the 
top and bottom of the Digital Temperature Controller.

E5ED-800

Precautions for Correct Use

Adapter

Waterproof packing 

Panel

E53-COV17
Terminal Cover 
(Sold separately.)

Adapter

E53-COV23
Terminal Cover
(Sold Separately)

Fastening 
screws

Terminal Cover
(E53-COV17) 
(Sold separately.)

Adapter

• E53-COV17

• E53-COV23

Enlarged Illustration of 
Terminal Section

Slightly bend 
the E53-COV23 
Terminal Cover 
in the direction 
shown by the 
arrows to attach 
it to the terminal 
block.

Adapter

Waterproof packing 

Panel

E53-COV24
Terminal Cover 
(Sold Separately)

Adapter

E53-COV24
Terminal Cover 
(Sold Separately)

Fastening screws

Содержание E5CD-800



















































Отзывы: