manualshive.com logo in svg
background image

1.

 Constitution of the Radio Frequency Keyless Entry   

    System with Door Lock Controller for vehicle

 

 

 

    The radio frequency keyless entry is a system that it controlls locking and unlocking the door by 

wireless remote controller. This system consists of two components. The TRANSMITTER is a device that 

transmits the signal when the button is pressed. The transmission signal consists of several synchronous 

codes, unique identification code, security code and function code. The RECEIVER is fixed inside the 

vehicle. It works intermittently to prevent the battery exhaustion. When the receiver detects the 

synchronous code, it runs continuously to receive the signals completely. After receiveing the signal, the 

receiver decides which operation will be performed. The user can select the following operations by 

pressing the button of the remote transmitter. 

 

OPERATION ACTION 

LOCK 

Lock the door 

UNLOCK 

Unlock the door 

Open the window

 

PANIC 

Beep the horn and flush the small light. (it continues 30 seconds) 

 

This receiver also controls wired operation. When the key is in the driver’s side key cylinder, all doors will 

Unlock if the key is turned to UNLOCK and hold more than one second. In case of the operation time is shorter, 

the only diver’s side door is mechanically unlocked. It is also available to control the door lock status by using 

the remote door control switch(both driver’s and passenger’s side). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transmitter 

f = 313.85MHz 

- 1 - 

Содержание 50J6















Отзывы: