Omntec FuelCheck Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 42

Omntec FuelCheck Скачать руководство пользователя страница 19

18

9. If the fiberoptic connectors are to be installed after the fiber is pulled into the conduit, it is im-

perative that sufficient excess (<10 ft) be left on each end so that the connectors can be at-
tached conveniently.

10. The procedures for installation of the fiberoptic connectors on the fiberoptic cable is specific to

the cable type and the connector type, and must be performed by a trained technician.
These instructions assume the fiberoptic cable has already been performed.

11. Due to possible wide temperature changes, a stabilizer is required over the connectors and

mating sleeve located in the probe conduit j-box. The following steps will perform this re-
quirement..

a) Spread open the slit and place the stopper over the fiberoptic interconnect cable and the

FuelCheck

®

probe cable as shown. Attach the ST mating sleeve to the ST connector on

the interconnect cable.

b) Attach stabilizer tube to stopper as shown leaving the connector protruding from the end.

c) Apply a small dab of optical gel to the tips of the Probe ST connector by dipping it into the

optical gel container. Be careful not to allow any dirt to get into the gel.

Figure 24

Insert fiber in stopper

Figure 25

Attach Stabilizer Tube

Figure 26

Apply optical gel

FU-FO-CN

(fiberoptic connector)

FU-FO-MS

(fiberoptic mating sleeve)

«
...
17
18
19
20
21
...
»

Содержание FuelCheck











































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды