OM100, OM300 & OM500 – QUICK REFERENCE GUIDE
Page 5 of 6
Audit Log
Location #123456 BAT:3
Mon 00/00/01 08:00am
1-More 2-Reprint CL-Done
Access Level Menu
1-Unlock 2-Code 3-Lock
4-Shutdown
Schedule Menu
1-Add 2-Remove 3-Verify
4-Copy 5-CLR 6-Holiday
Setup Menu
1-Status Report 2-Clock
3-Defaults 4-Autocodes
5- Run Diagnostics
Codes Menu
1-Users 2-Service 3-Audit
4-Submasters 5-Master
1-Audit
3-Access
4-Schedule
5-Setup
2-Codes
Main Menu
1-Audit 2-Codes 3-Access
4-Schedule 5-Setup 0-End
This chart is for general reference only.
Specific features may vary with software
ENTER MASTER CODE, WAIT FOR 3 GREEN
FLASHES THEN ENTER "99"
This chart is intended for use
with OMNILOCK printer WP4000.
1-Add 2-Remove 3-Verify
4-Hold 5-Restore 6-Time Limit (00:00)
510: # digit Pin?
2-Service
1-Add 2-Remove 3-Verify
4-Hold 5-Restore
511: # digit Pin?
3-Audit
1-Add 2-Remove 3-Verify
4-Hold 5-Restore
Submaster ID (###)?
4-Submaster
New Code Length (4-9)?
5-Master
Warning- New Code Length!
All Codes Will Be Erased
Continue? 1-Yes 2-No
Enter New Master Pin
Reenter Code To Confirm
Master Code Set
Print Pins? 1-Yes 2-No
Print Groups? 1-Yes 2-No
Starting ID (###)?
Ending ID (###)?
3-Verify
Hold ID (###)?
4-Hold
Restore ID (###)?
5-Restore
Starting ID (###)?
Ending ID (###)?
Select User Groups
(1-4, 5-All, CL-Done)
6-Groups
Extended User Type?
1-Supervisor 2-Manager
Extend User ID(###)?
7-Extend
Starting ID (###)?
Ending ID (###)?
Remove Users ###-###?
1-Yes 2-No
2-Remove
Schedule(Mon-1 . . Day-9)?
Add Mon Time (24 HR)?
1-Unlock 2-Code 3-Lock
Access Level?
Unlock With First Code?
1-Yes 2-No
Select Groups To Enable
(1-4, 5-All, CL-Done)
Group #1 Supervised?
1-Add
Status Report
Location #123456 BAT:3
Mon 00/00/01 08:00am
Access: C/R + + + +
Open Delay Seconds: 02
Daylight: Northern
Service Code Time: 00:00
Battery Usage: 000
1-Status
Remove (dd) Time (24 HR)?
Remove Mon 08:00am?
1-Yes 2-No
2-Remove
In Use: #
Schedule (Mon-1 . . Day-9)?
3-Verify
Copy From:
Schedule (Mon-1 . . Day-9)?
Copy(dd) To:
Schedule (Mon-1 . . Day-9)?
4-Copy
Select Schedule To Clear
(Mon-1 . . Day-9, 0-All)?
Clear All Schedules?
1-Yes 2-No
5-Clear
1-Add 2-Remove 3-Verify
4-Clear Holiday list (00:00)
Month (mm)?
Day (dd)?
Schedule (Mon-1 . . Day-9)?
6-Holiday
Month (mm)?
Day (dd)?
Year (yy)?
Time: (24 HR)?
2-Clock
Defaults Menu
1- Open delay Seconds: 02
2- Daylight: Northern
3- Group Boundaries
4- Location: 123456
3-Defaults
Facility Autocodes
1- 000000 2- 000000
3- 000000 4- 000000
6 Digit Autocode? (enter 6 digits)
4-Autocodes
-- Diagnostics Report --
OMNILOCK 500 vX.XX
(c) OSI SECURITY DEVICES
LOCATION #000000 BAT:3
5-Run Diagnostics
User Codes Menu
1-Add 2-Remove 3-Verify
4-Hold 5-Restore 6-Groups
7-Extend
1-Users
(1-4) Autocode 5-Manual
Starting ID (###)?
Ending ID (###)?
1-Add
NOTE: (1-4)Autocode only
works when it has been Setup
in the lock
Unlock With First Code?
1-Yes 2-No
1-Unlock
Select Groups To Enable
(1-4, 5-All, CL-Done)
Group # Supervised?
1-Yes 2-No
Access: C/R + + + +
2-Code
Access: Lockout
3-Lock
Access: Shutdown
4-Shutdown
NOTE: Access: C/R + + + +
(Code Required for four(4)
groups; Where + = enabled,
- = disabled, and
s = supervised)
To Reset The Lock To The Default Master Code:
Press and hold the Reset Button until the light flashes green on the keyboard. The system will
perform a self-test and then flash green five(5) times. Any red flashes indicate an electronics or
drive problem.
The Master Code is now set back to the factory default of
, and all programming
has been erased.
To log on and begin programming, enter Master Code and use Command # 99.
Reset Button
