background image

 

The Omegon® Advanced Dobson 203

 

Congratulations on the purchase of 
the new Omegon® Advanced 
Dobson 203 telescope. This 
telescope will give you hours of fun, 
with its optical glass mirrors and 
light gathering capability, it is the 
ideal companion to start in the 
world of amateur astronomy. With 
this telescope you will be able to see 
the craters on the Moon, star 
clusters, many nebulae, the Jupiter’s 
disc features and its Galilean moons 
and the rings of Saturn, Mars and 
Venus and many more objects.

 

Included parts.

 

The telescope is 

supplied either as a basic set or 
as a complete set, or as a 
personalized set (configured at 
purchase) - please check which 
version you purchased – the 
following instructions are valid 
for basic and complete set. The 

basic set does not include any accessories, only the optical tube and base. At the end of this 
Instruction Manual you will find the available accessory list which includes focuser, eyepieces, 
finderscope and eyepiece rack for completion of your telescope if necessary

 

1. Knowing your telescope. 

1- Spider (secondary mirror)   

 

6- Balance adjustment knob    

 

11- Flat head bolt (point) 

2- Finderscope shoe 

 

 

7- Flat head bolt;   

 

 

12- Rubber foot 

3- Focuser base 

 

 

 

8- Left panel; 

 

 

 

13- Right panel 

4- Optical tube 

 

 

 

9- Top base disc; 

 

 

 

14- Front panel’s holes 

5- Primary mirror cell 

 

 

10- Bottom base disc; 

 

 

2. Getting Started. 

The telescope is supplied with two boxes marked OTA 1/2 and Base 2/2. Each 

containing the optical tube and the Dobson base respectively. Start by opening the smaller flat box 
(should be marked Base 2/2). Remove the wooden panels, the tools and accessories. Place them on 
a flat and soft surface (we recommend carpeted floor to avoid scratches). 

3. Assembly.

 

Start by 

setting the side panels and front panel together. Use the supplied Allen wrench and the flat bolts 
with pointed tip #11 (as shown in fig. 2). Make sure that the front panel’s two eyepiece-rack holes 
are pointing out (the two white arrow as show in fig. 1). This is important because the eyepiece-rack 
(not included) may be fixed to those two holes. Start with one of the side panels and the move to 
the other one. Make sure the front panel is mounted upwards as shown in fig. 1. Now place the top 
base disc as shown in fig 3.  You will need another 6 Flat head bolts, as used before. For each hole 
there is a recess on the Top base disc where the flat head bolts thread. Make sure to place the 
surface with the recess oriented to the outside. Use the supplied Allen wrench as shown in figure 4. 
At this point all panels and Top base disc should be firmly tightened. Now place the Bottom base disc 
as shown in fig. 6. Use the supplied bolt, nuts, and washer and central shaft to assemble as shown in 
fig. 7. Correct placement is very important. Start by inserting the aluminium tube (shaft – part 4 
fig.7) -text continues page 6. 

Figure 1. Parts description.

 

Содержание Dobson Advanced 203














Отзывы: