![background image](http://html1.mh-extra.com/html/omega/oru52xl/oru52xl_user-manual_4096434009.webp)
09
User Manual
Safety Precautions
•
Before cleaning your rangehood or performing any
maintenance, please ensure that the rangehood is turned
off at the power point.
•
Do not use abrasive cleaners to clean the rangehood. We
recommend the use of warm soapy water and a cloth.
•
Ensure that the rangehood is cleaned regularly, as a
build-up of grease and fat may occur otherwise.
•
The filters on the rangehood must be cleaned regularly
to maintain efficiency, and prevent grease build up.
•
The filter mesh is made of a high-density stainless steel.
It is recommended that this is undertaken every 4–6
weeks, depending on frequency of use. The filters can be
cleaned with warm soapy water or a cloth.
•
Cleaning of the rangehood must be performed as
described above; otherwise there is a possibility of a fire
hazard due to grease and fat build up.
Replacing the LED lights
WARNING:
Before attempting to replace the lights,
ensure that the appliance is switched off and unplugged
from the wall.
•
Remove the aluminium filter.
•
Press the lamp face and turn anti-clockwise to remove.
•
Replace with the same type of bulb (GU10 Base, 3W MAX).
• Max Wattage: 2 x 3W
• Voltage Range: 220 – 240V AC
• ILCOS D Code: DR-3/65/1B-H-GU10-46/50
•
Replace the aluminium filter.
NOTE:
The diagram images in this user manual are for explanatory purposes only. Your appliance may appear differently.
Cleaning & Maintenance
6
Installation Instructions
Please ensure that all power is switched off before installing the range hood.
Installation must be in accordance to the local electrical authority and codes.
The switched power outlet for the range hood should be positioned to enable the user to turn the power off,
to enable cleaning and any maintenance required.
The switched power outlet should be installed within 600mm from the rear of the unit.
Ensure that when installing the range hood, that it is protected from any possible damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority.
Ensure that the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is structurally sound.
Before using the appliance, remove the plastic coatings protecting the stainless-steel finish.
These models are intended to be installed into kitchen cabinetry. Take care that the cabinetry and
supporting wall can carry the weight of the rangehood.
Always double-check dimensions in this manual against the appliance before commencing.
The rangehood should be placed at a minimum distance of 650mm from the cooking surface of the cooker
below. Any more than 750mm could compromise the performance of the appliance. Drill a hole in the
cupboard, 490*265mm for model ORU52XL and 665*265mm for model ORU70XL. Make sure the distance
between the edge of the hole and the edge of the cupboard edge is at least 35mm. Remove the filter and
remove the four screws holding the lower panel in place. Lift the appliance into the hole and check that it fits
correctly (no gaps, does not interfere with anything above it etc.). Mark the hole positions with a pencil
remove the appliance and pre-drill the holes using a small drill bit. Place the appliance back into position,
line up the holes and fix into place using the 8 screws provided. Replace the cover & fix into position with
the 4 screws and fit the filter. Fit the one-way filter to the top of the unit.
The exhaust air vents through the one-way valve at the top. If the exhaust is to be vented away, cut a hole
(~Ø160mm) in the top of the cupboard, and connect Ø150mm ducting to the one-way valve & pass it
through the hole to wherever it is going. If the exhaust air is to be recirculated back into the room, either cut
vents into the cupboard (with a minimum area of 800cm²), or leave the cupboard door open when in use.
Once assembled in place, the appliance can be connected to the power supply.
Operating Instructions
Note
: Before the unit can be operated, it must either be ducted
or, if the model is installed as a re-circulating range hood, it
must be fitted with charcoal filters (one set supplied with the
appliance).
With the appliance fully installed and the power connected, the
appliance can be used.
•
The light can be turned on & off by pressing the
Light button.
•
The fan can be turned on and adjusted by pressing any of the three fan speed buttons (Low, Mid
& High).
•
The fan can be turned off by pressing the Stop button.
7
Replacing the LEDS
Warning: Before attempting to replace the lights, ensure that the appliance is
switched off and unplugged from the wall.
•
Remove the aluminium filter.
•
Press the lamp face and turn anti-clockwise to remove.
•
Replace with the same type of bulb (GU10 Base, 3W MAX).
o
Max Wattage: 2 x 3W
o
Voltage Range: 220 – 240V AC
o
ILCOS D Code: DR-3/65/1B-H-GU10-46/50
•
Replace the aluminium filter.
Cleaning
SAFETY PRECAUTION
Before cleaning your rangehood or performing any maintenance,
please ensure that the rangehood is turned off at the power point.
Do not use abrasive cleaners to clean the rangehood. The use of
warm soapy water and a cloth are recommended.
Ensure that the rangehood is cleaned regularly, as a build-up of
grease and fat may occur otherwise.
The filters on the rangehood must be cleaned regularly to maintain efficiency, and prevent grease build up.
The filter mesh is made of a high-density Stainless Steel. It is recommended that this is undertaken every 4
– 6 weeks, depending on frequency of use. The filters can be cleaned with warm soapy water or a cloth.
Cleaning of the rangehood must be performed as described above; otherwise there is a possibility of a fire
hazard due to grease and fat build up.
Troubleshooting
Fault
Possible Cause
Solution
Light on, but motor
does not work
Fan switch turned off
Select a fan switch position.
Fan switch failed
Contact Everdure Service.
Motor failed
Contact Everdure Service.
Light does not work,
motor does not work
House fuses blown
Reset/Replace fuses.
Power cord loose or disconnected
Refit cord to power outlet.
Switch power outlet on.
Oil leakage
One-way valve and the air ventilation
entrance are not tightly sealed
Take down the one-way valve and seal
with sealant.
Leakage from the connection of U-
shaped section and cover
Take U-shaped section down and seal.
Lights not working
Broken/Faulty LED lamp
Contact Everdure Service.
Insufficient suction
The distance between the rangehood
and the gas top is too far
Refit the rangehood to the correct
distance.
The Rangehood
inclines
The fixing screw not tight enough
Tighten the hanging screw and make it
horizontal.
6
Installation Instructions
Please ensure that all power is switched off before installing the range hood.
Installation must be in accordance to the local electrical authority and codes.
The switched power outlet for the range hood should be positioned to enable the user to turn the power off,
to enable cleaning and any maintenance required.
The switched power outlet should be installed within 600mm from the rear of the unit.
Ensure that when installing the range hood, that it is protected from any possible damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority.
Ensure that the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is structurally sound.
Before using the appliance, remove the plastic coatings protecting the stainless-steel finish.
These models are intended to be installed into kitchen cabinetry. Take care that the cabinetry and
supporting wall can carry the weight of the rangehood.
Always double-check dimensions in this manual against the appliance before commencing.
The rangehood should be placed at a minimum distance of 650mm from the cooking surface of the cooker
below. Any more than 750mm could compromise the performance of the appliance. Drill a hole in the
cupboard, 490*265mm for model ORU52XL and 665*265mm for model ORU70XL. Make sure the distance
between the edge of the hole and the edge of the cupboard edge is at least 35mm. Remove the filter and
remove the four screws holding the lower panel in place. Lift the appliance into the hole and check that it fits
correctly (no gaps, does not interfere with anything above it etc.). Mark the hole positions with a pencil
remove the appliance and pre-drill the holes using a small drill bit. Place the appliance back into position,
line up the holes and fix into place using the 8 screws provided. Replace the cover & fix into position with
the 4 screws and fit the filter. Fit the one-way filter to the top of the unit.
The exhaust air vents through the one-way valve at the top. If the exhaust is to be vented away, cut a hole
(~Ø160mm) in the top of the cupboard, and connect Ø150mm ducting to the one-way valve & pass it
through the hole to wherever it is going. If the exhaust air is to be recirculated back into the room, either cut
vents into the cupboard (with a minimum area of 800cm²), or leave the cupboard door open when in use.
Once assembled in place, the appliance can be connected to the power supply.
Operating Instructions
Note
: Before the unit can be operated, it must either be ducted
or, if the model is installed as a re-circulating range hood, it
must be fitted with charcoal filters (one set supplied with the
appliance).
With the appliance fully installed and the power connected, the
appliance can be used.
•
The light can be turned on & off by pressing the
Light button.
•
The fan can be turned on and adjusted by pressing any of the three fan speed buttons (Low, Mid
& High).
•
The fan can be turned off by pressing the Stop button.
7
Replacing the LEDS
Warning: Before attempting to replace the lights, ensure that the appliance is
switched off and unplugged from the wall.
•
Remove the aluminium filter.
•
Press the lamp face and turn anti-clockwise to remove.
•
Replace with the same type of bulb (GU10 Base, 3W MAX).
o
Max Wattage: 2 x 3W
o
Voltage Range: 220 – 240V AC
o
ILCOS D Code: DR-3/65/1B-H-GU10-46/50
•
Replace the aluminium filter.
Cleaning
SAFETY PRECAUTION
Before cleaning your rangehood or performing any maintenance,
please ensure that the rangehood is turned off at the power point.
Do not use abrasive cleaners to clean the rangehood. The use of
warm soapy water and a cloth are recommended.
Ensure that the rangehood is cleaned regularly, as a build-up of
grease and fat may occur otherwise.
The filters on the rangehood must be cleaned regularly to maintain efficiency, and prevent grease build up.
The filter mesh is made of a high-density Stainless Steel. It is recommended that this is undertaken every 4
– 6 weeks, depending on frequency of use. The filters can be cleaned with warm soapy water or a cloth.
Cleaning of the rangehood must be performed as described above; otherwise there is a possibility of a fire
hazard due to grease and fat build up.
Troubleshooting
Fault
Possible Cause
Solution
Light on, but motor
does not work
Fan switch turned off
Select a fan switch position.
Fan switch failed
Contact Everdure Service.
Motor failed
Contact Everdure Service.
Light does not work,
motor does not work
House fuses blown
Reset/Replace fuses.
Power cord loose or disconnected
Refit cord to power outlet.
Switch power outlet on.
Oil leakage
One-way valve and the air ventilation
entrance are not tightly sealed
Take down the one-way valve and seal
with sealant.
Leakage from the connection of U-
shaped section and cover
Take U-shaped section down and seal.
Lights not working
Broken/Faulty LED lamp
Contact Everdure Service.
Insufficient suction
The distance between the rangehood
and the gas top is too far
Refit the rangehood to the correct
distance.
The Rangehood
inclines
The fixing screw not tight enough
Tighten the hanging screw and make it
horizontal.
Содержание ORU52XL
Страница 13: ...13 User Manual Notes...