background image

OM-USB-1208HS Series User's Guide 

Functional Details 

13 

Each channel can be software-paced at rates up to 5,000 updates per second (system-dependent), or hardware-
paced at rates up to 1 MS/s.  

Each analog output on the OM-USB-1208HS-2AO and OM-USB-1208HS-2AO has a fixed ±10 V output 
range. The outputs default to 0 V at power up. 

External clock I/O 

Use the 

AICKI

 and 

AOCKI 

terminals to receive a sampling clock from an external source. 

Use the 

AICKO

 terminal to output the internal A/D sampling clock. Use the 

AOCKO

 terminal to output the 

internal D/A sampling clock. When using an external clock, a pulse output generated by the external clock 
rising edge is also available at these terminals. 

Refer to Figure 3 on page 11 for the location of these pins. 

Digital I/O 

You can connect up to 16 digital I/O lines to screw terminals 

DIO0

 through 

DIO15

. Refer to Figure 3 on page 11 

for the location of these pins.  

The 16 DIO terminals have 47 k resistors that you can configure for pull-up/pull-down using a jumper inside the 
case. The default configuration is pull-down. 

You can use the digital I/O terminals to detect the state of any TTL-level input. Refer to the schematic shown in 
Figure 5.  

 

Figure 5. Schematic showing switch detection by digital channel DIO0 

If you set the switch to the +5 V input, DIO0 reads 

TRUE

 (1). If you move the switch to GND, DIO0 reads 

FALSE

 (0). 

Internal pull-up/pull-down capability 

Each of the 16 DIO bits on the has a 47 kΩ pull-up/pull-down resistor. To configure these bits for either a +5 V 
pull-up or a 0 V pull-down option, you must open the device case to access the three-pin jumper labeled 

W34

.  

The pull-up/pull-down voltage is common to all of the internal 47 kΩ resistors.  

To open the case and set the W34 jumper, do the following. 

1.

 

Turn the device over and rest the top of the housing on a flat, stable surface. 

2.

 

Peel off the four rubber feet on the bottom of the device to access the screws. 

3.

 

Remove the four screws from the bottom of the device. 

4.

 

Hold both the top and bottom sections together, turn the device over and rest it on the surface, then 
carefully remove the top section of the case to expose the circuit board. 

5.

 

Configure jumper 

W34

 for either pull-up or pull-down. The jumper is configured by default for pull-down 

(see Figure 6 and Figure 7). 

Содержание OM-USB-1208HS Series


























Отзывы: