![background image](http://html2.mh-extra.com/html/omega/om-el-wifi-series/om-el-wifi-series_quick-start_3984172002.webp)
START HERE
Windows ™ XP/ Vista/ 7
OM-EL-WiFi Configuration Software Installation
Getting Started
Installing Software
Sensor Settings
Sensor Placement
Hints and Tips
Important Safety Instructions
Copyright Omega Engineering, Inc. 2013 Issue 1 02/13
The sensor will arrive partly charged but ideally you
should charge it for 24 hours before use for optimum
performance. The sensor will automatically start
recharging while connected to a PC or USB charger using
the USB cable provided.
The battery icon has three states:
Not Displayed
Battery OK
1
Solid
Battery Charging
3
Flashing
Battery Low - Recharge!
2
The sensor may already be displaying a reading but it will
not be confi gured or connected to your WiFi network until
you complete the product set-up.
To set up the unit use our free EasyLog WiFi PC software
available to download from the ‘Software’ section at
www.omega.com.
Connect the OM-EL-WiFi Sensor to the PC’s USB port with
the USB cable provided.
Double click on the EasyLog WiFi icon on your Windows™
desktop. This will load the wizard confi guration software.
Follow the on-screen instructions to set up your sensor.
Note:
These screens will vary depending on which sensor model purchased.
Click on the ‘Set-Up Sensor’
button
1
Set High & Low Alarms
4
Name your Sensor, Select
Temperature Scale, Sample
Rate & Transmission Rate
3
Position your Sensor where
you wish to take readings
6
Click on your network and
enter your password if
required
2
Sensor Set-up is now complete
5
When placing the sensor consider local heat sources and
radio obstructions. Any physical obstructions between
router and sensor will affect the signal range. WiFi
extenders can also be used to increase range.
2
the sensor is not communicating with
the EasyLog WiFi software
Flashing
2
the sensor has not yet been set-up
and confi gured to a WiFi network
Not Displayed
1
the sensor is successfully communicating
with the EasyLog WiFi software
Solid
3
The Signal icon has three states:
Use the
button on the home screen to get more
help on setting up your sensors.
Sensors can be confi gured over the air without reconnecting
the USB cable.
Changing Sensor Settings over Air
Battery Replacement
The rechargeable battery in the EasyLog product should only be
replaced by Omega Engineering.
Repairing or Modifying
Never attempt to repair or modify EasyLog products. Dismantling
EasyLog products, including the removal of external screws, may
cause damage that is not covered under the warranty. Servicing
should only be provided by Omega Engineering. If the EasyLog
product has been submerged in water, punctured, or seriously
damaged do not use it before returning it to Omega Engineering.
Charging
Only use a USB Power Adaptor or a USB port on another device to
charge EasyLog products. Read all safety instructions for any third
party products and accessories before use with this product. Omega
Engineering is not responsible for the operation of any third party
accessories or their compliance with safety and regulatory standards.
We do not recommend charging the battery when the unit is at 40˚C
(104˚F) or above. Some of our products employ safety features to
prevent this.
Using Connectors and Ports
Never force a connector into a port; check for obstruction in the
port, make sure that the connector matches the port and that you
have positioned the connector correctly in relation to the port. If the
connector and port do not join with reasonable ease they probably do
not match and should not be used.
Disposal and Recycling Information
You must dispose of EasyLog products according to relevant laws and
regulations. EasyLog products contain electronic components and
Li-Po batteries and therefore they must be disposed of separately
from household waste.
WARNING:
Failure to follow these safety instructions could result
in fi re, electrical shock, other injury or damage.