background image

Installation Instructions 

Electrical Connection 

1.

Your oven requires 16 Amp fuse and must be installation by a qualified electrician.

2.

Your oven is adjusted in compliance with 220-240V AC/380-415V AC 50/60Hz. electric supply. If

the mains are different from this specified value, contact your authorized service.

3.

Electrical connection of the oven should only be made by the sockets with earth system installed

in compliance with the regulations. If there is no proper socket with earth system in the place

where the oven will be placed, immediately contact a qualified electrician. Manufacturer shall

never be responsible from the damages that will arise because of the sockets connected to the

appliance with no earth system. If the ends of the electrical connection cable are open,

according to the appliance type, make a proper switch installed in the mains by which all ends

can be disconnected in case of connecting / disconnecting from / to the mains.

4.

If your electrical supply cable gets damaged, it should be replaced by an authorized service or

qualified electricians immediately in order to avoid the danger.

5.

Electrical cable should not touch the hot parts of the appliance.

6.

Please operate your oven in a dry atmosphere.

Gas Connection 
WARNING

: Before starting any work related with gas installation, turn off the gas supply. Risk of explosion. 

1.

Fit the clamp to the hose. Push on the hose until it goes to the end of the pipe.

2.

For the sealing control; ensure that the buttons in the control panel are closed, but the gas

cylinder is open. Apply some soap bubbles to the connection. If there is gas leakage, there will

be foaming in the soaped area.

3.

The oven should be used a well ventilation room and should be installed on flat ground.

4.

Re-inspect the gas connection.

5.

When placing your oven in its location, ensure that it is at the counter level. Bring it to the

counter level by adjusting the feet if necessary.

6.

Do not route the gas hose and electrical supply cable of your oven through heated areas,

especially through the rear side of the oven. Do not move the oven with the gas connected as

this can cause a gas leak.

7.

Please use a flexible hose for gas connection.

Содержание OF909FX



























Отзывы: