background image

 

13 

 

Maintenance 

Clean burner tops and trivets at least once a week, or after any spillage.

 

Check injectors are not blocked and 

the electrode and probe are clean. 

Gas inlet pipes should be checked periodically for leakages (see section on leak testing) a minimum of every 

12 months. 

Lubrication of gas valves - This can only be performed by an authorised person. It may be required if the gas 

tap become stiff and difficult to turn.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fault 

Possible cause  (corrective action) 

No spark / No ignition 

of gas. 

Power outage, appliance power turned off at isolation switch, fuse blown / tripped, no gas to the 

appliance (check supplies). Spillage of liquid over burner (clean up spillage on burner components). 

Burner not assembled correctly (Refer to assembly instruction manual). 

Burner ignites but flame 

goes out when control 

knobs released.   

Control knob not depressed down enough when igniting burner, control knob being released from 

the ignition mode too early (try ignition again).  Spillage of liquid over burner (clean up spillage on 

burner components). Burner not assembled correctly (Refer to assembly instruction manual). Faulty 

thermocouple (technician call out required call Service Centre). 

Erratic / Abnormal 

flames or noise when 

operating the 

appliance.  

Burner not assembled correctly (Refer to assembly instructions). Spillage of liquid over burner 

(Clean up spillage on burner components). Oversize cooking vessel being used on the appliance 

(use smaller cooking vessels). Internal ignition of burner (Turn off gas and reignite burner). Wrong 

gas type being used (check supply and data labels).  

Содержание OCG905X

















Отзывы: