background image

 

WOK BURNER MAINTENACE & ASSEMBLY 

When fitting the wok burner together, it is very important to check that the burner 
flame distributor (F) and the cap (C) are correctly positioned (fig. 6). Failure to do 
so can cause problems with ignition and also the way in which the burner 
operates.  
Check that the electrode (S) is always clean to ensure trouble-free sparking. 
Check that the probe (T) is always clean to ensure correct operation of the safety 
valves (for models with safety device). 
The Wok burner must be correctly positioned (see fig.7). The burner rib must lock 
into position on the assembly below. If positioned correctly, the burner will not 
rotate (fig.8). 
Then position the enamel cap A and the enamel ring B (fig.8). 
The four holes around the outside of the crown must always be kept 
clean. 

When cleaning, remove the flame divider (fig.9) and use a cotton bud, 
toothbrush, or a stiff wire brush to clean out any incrustations or dirt 
from the four holes marked “H” (fig.10). 

This procedure is necessary to ensure the burner functions correctly.   

 

 

MAINTENANCE 

Clean burner tops and trivets at least once a week, or after any spillage.

 

Check injectors are not blocked 

and the electrode and probe are clean. 
Gas inlet pipes should be checked periodically for leakages (see section on leak testing)  a minimum of 
every 12 months. 
Lubrication of gas valves - This can only be performed by an authorised person. It may be required if the 
gas tap become stiff and difficult to turn.  

 

 

 

 

 

 

 

Fault 

Possible cause  (corrective action) 

No spark / No ignition 
of gas. 

Power outage, appliance power turned off at isolation switch, fuse blown / tripped, no gas to the 
appliance (check supplies). Spillage of liquid over burner (clean up spillage on burner components). 
Burner not assembled correctly (Refer to assembly instruction manual). 

Burner ignites but flame 
goes out when control 
knobs released.   

Control knob not depressed down enough when igniting burner, control knob being released from 
the ignition mode too early (try ignition again).  Spillage of liquid over burner (clean up spillage on 
burner components). Burner not assembled correctly (Refer to assembly instruction manual). Faulty 
thermocouple (technician call out required call Service Centre). 

Erratic / Abnormal 
flames or noise when 
operating the 
appliance.  

Burner not assembled correctly (Refer to assembly instructions). Spillage of liquid over burner 
(Clean up spillage on burner components). Oversize cooking vessel being used on the appliance 
(use smaller cooking vessels). Internal ignition of burner (Turn off gas and reignite burner). Wrong 
gas type being used (check supply and data labels).  

10 

Содержание OCG60X













Отзывы: