background image

 

 

Operation Instructions 

The hob is controlled by pressing the appropriate electronic button. Each button pressed is followed by a 

buzzer sound. 

 

1. 

Heater display 

2. 

Activate/Deactivate heater 

3. 

Heat setting decrease 

4. 

Heat setting increase 

5. 

Decimal point 

6. 

Key lock indicator 

7. 

Key lock 

8. 

On/Off 

Mode Descriptions

 

Stand-By-

Mode

 

S-Mode

 

Mains supply is applied to 

the hob control and all 

heater displays are off or a 

residual heat display is 

active.

 

Operating- 

Mode

 

B-Mode

 

At least one heater display 

shows a heat setting 

between ´

0

` and ´

9

`.

 

Lock Mode

 

VR-Mode

 

The hob control is locked.

 

Switching the Appliance On and Off 

• 

•  If the appliance is in Stand-By mode, it is put in Operating mode by pressing the On/Off 

button   for at least 1 second. A buzzer will sound to indicate the successful operation. 

• 

A “

0

” will appear on all heater displays and all decimal points corresponding to the heaters will 

flash (1 second on, 1 second off). 

• 

If there is no operation within 10 seconds, all heater displays will switch off. 

• 

If the displays do switch off, the heater will be sent into Stand-By mode. 

• 

•  If   is pressed for more than 2 seconds (in Operating mode), the appliance will switch off 

and will enter S-Mode again. The appliance can be switched off by pressing   at any time; even 

if other buttons are pressed simultaneously. 

• 

If there is any residual heat from a heater, this will be indicated in the corresponding heater 

display. 

Selecting a Heater 

If a single heater is chosen with the corresponding Activate/Deactivate Heater Button  , the decimal point 

of the heater display will flash. For the selected heater, you can set the heat level between 1 and 9 by 

pressing the Heat Setting Buttons   or  . 

The buttons must be pressed within 3 seconds of selecting a heater, otherwise the heater selection will be 

erased and the heat setting decimal point will disappear. If there is no further operation within 10 seconds, 

the heater reverts back to S-Mode. 

The heat setting can always be changed by pressing   or  . The available settings are between 1 and 9. 

Each button operation or each display change is accompanied by a buzzer sound. 

 

 

Содержание OC64TB















Отзывы: