![background image](http://html1.mh-extra.com/html/omega/excalibur-al-1810-edp/excalibur-al-1810-edp_operation-manual_3948244005.webp)
Page - 40
Feature #5 Stick Shift Remote Starting
Factory Default Setting
Off (
press
“disarm/unlock” button to program
)
Option:
On (
press
“arm/lock” button to program
)
This feature changes the parameters of the AL-1810-EDP’s remote start operation
to be suitable for manual transmission-equipped vehicles via a “setup” procedure
which must be followed upon exiting the vehicle. When this feature is turned on,
the operator must set the parking brake and then press the controller or transmitter’s
“arm/lock” and “disarm/unlock” buttons at the same time, which keeps the engine
running after removing the ignition key. After exiting, the user must then arm the
system, locking the vehicle doors, by pressing the “arm/lock” button. Only after
Feature #4 Turbo Timer
Factory Default Setting
Off
(
press
“arm/lock” button to program
)
Options:
Run 1 Minute
(
press
“disarm/unlock” button to program
)
Run 2 Minutes
(
press
“
II
” button to program
)
Run 3 Minutes
(
press
“
III
” button to program
)
This feature, the operation of which is described on page 16, when turned on
configures the AL-1810-EDP to automatically keep the engine running briefly after
it is turned off. This operation is designed specifically for vehicles having
turbocharged engines (the user may temporarily bypass the feature if desired).
This feature should only be programmed by the installer, and the operation of
this feature depends on the correct connection of the safety wire to the vehicle’s
parking brake. Please refer to the Installation Instructions manual for proper
connection of this wire.
Feature #3 Horn Output Functions
Factory Default Setting
Horn Output
(
press
“arm/lock” button to program
)
Options:
Door Unlock
(
press
“disarm/unlock” button to program
)
Ignition Output
(
press
“
II
” button to program
)
Accessory Output
(
press
“
III
” button to program
)
This is the second of two multi-use outputs which can be programmed to perform
several different functions. The primary function of this output, is that it is available
to operate the vehicle’s existing horn; either in conjunction with the electronic siren,
or in place of the siren. Using both the siren and the horn creates an extremely
effective security system with unique theft deterrence capabilities.
Optionally, if desired or needed, this output can be programmed to be door
unlock, or as additional ignition or accessory outputs, if needed for remote starting
use.
•
Pressing the “arm/lock” and “disarm/unlock” buttons together activates the
remote starting feature of the Excalibur AL-1810-EDP.
The
1-Way Transmitter
The
2-Way Controller
“
III
” button
“
II
” button
“
P
”rogram
button
Page - 5
“
III
” button
“
II
” button
“
arm/lock
”
button
“
disarm/unlock
”
button
“
arm/lock
”
button
“
disarm/unlock
”
button
“
arm/lock
”
•
Pressing and releasing the “arm/lock” button arms the security system and
locks the doors.
•
Pressing and holding this button for three seconds will first arm, and then
activate the Panic feature, locking the doors.
“
disarm/unlock
”
•
Pressing and releasing the “disarm/unlock” button disarms the system and
unlocks the doors unless the alarm is triggered, in which case it will disarm the
activated alarm, but not unlock the doors unless the button is pressed again.
•
Pressing and holding this button for three seconds will first disarm, and then
activate the Panic feature, unlocking the doors.
•
The unlock operation may be optionally configured during the system’s
installation so that pressing this button once disarms the system and unlocks
only the driver's door, and pressing a second time unlocks all of the doors.