![background image](http://html1.mh-extra.com/html/omega/excalibur-al-1000-edp/excalibur-al-1000-edp_operation-manual_3944801011.webp)
Page - 11
Automatic Rearming Feature:
Automatic Rearming is a programmable
feature which ensures that your system is never inadvertently disarmed. It is
possible to accidentally or unknowingly operate the transmitter from a pocket or
purse. You may not even be aware of an accidental disarming due to the enhanced
operating distance offered by the Excalibur’s extended range, it is not noticed.
Automatic Rearming has the alarm rearm itself 90 seconds after it has been
disarmed, unless a vehicle door is opened and the ignition key turned on. Automatic
Rearming is confirmed by a fast flashing Status Light after the disarming, unless the
system was triggered, in which case a Zone Violation code will flash instead.
During the 90 second period, Automatic Rearming can be paused by opening
the door or stopped completely by turning the ignition key "on". Also, Automatic
Rearming can be cancelled by the Safety Disarm/Storm Mode feature; if the system
is disarmed while triggered, Automatic Rearming will not occur.
Disarming the System by Emergency Override
Should the transmitter become lost, damaged, or its batteries become exhausted,
the Valet Switch and the vehicle’s ignition key may be used to disarm the system:
Step 1
With the system in the armed condition, enter the vehicle via the driver's
door (be aware that the alarm will trigger when the door is opened).
The number of Valet Switch presses which are required for the Emergency
Override is custom-programmable! This is the SecureCode feature, which is
described on page 15. The above Emergency Override instructions reflect the
“as received from the factory” default setting.
Step 3
Within 5 seconds press and release the Valet Switch one time. The system
will disarm.
Step 2
Using the ignition key, turn the vehicle’s ignition switch on.
Step 7
Allow 10 seconds to pass without performing any programming
actions, or turn the vehicle’s ignition on.
Exit Programming mode:
• The siren will sound briefly and the Status Light will go out.
Programmable Features Descriptions
To custom program a new SecureCode:
Step 3
After entering the first stage by pressing the “arm/lock” button the
desired number of times, and receiving a chirp for each press, wait for the
Step 2
Within 10 seconds slowly press and release the transmitter’s “arm/lock”
button the number of times equal to the desired SecureCode for stage 1,
allow the system to respond to each transmitter button press with a siren
chirp before pressing the button again.
Step 1
Follow Steps 1 to 4 in the previous “How to Program Features” instruc-
tions; at Step 4 the Valet Switch will be pressed and released once (the
siren chirps once) to access “feature #1”.
Feature #1 SecureCode
Factory Default Setting
1 Press
Options:
1 to 9 presses, in each of two stages
Step 4
Continue to configure stage 2 of the SecureCode by now pressing and
releasing the “disarm/unlock” button the number of times desired for the
stage 2. This should be done in the exact same fashion as the stage 1 entry-
press the “disarm/unlock” button, wait for a single chirp before pressing
the button again, and then when final button press is done, wait after the
single chirp for the siren to chirp the total number entered Valet Switch
entry.
system, after the final button press, to chirp the siren again the total
number of times that the button was pressed.
SecureCode is a unique patented feature which allows you to custom select the
number of Valet Switch presses in two stages, instead of a single “1 press”, which
would be required in order to perform an Emergency Override. If any of the three
anti-carjacking features are utilized, a customized SecureCode would also be
required to turn it off once it is fully activated. The SecureCode operation is
described on page 15.
Page - 22