7.
Press
/MAX. The display momentarily flashes
“rd 1”,
then shows the low calibrated value.
8.
a. If you selected “int,”
enter the desired display
corresponding to low input.
(0Vdc, 1Vdc, 4mA)
b. If you selected “LivE”,
apply low load to
sensor and enter desired display.
Press
/MAX and
/TARE to enter desired
display.
9.
Press MENU. The display momentarily flashes
“rd 2”,
then shows the high calibrated value.
10.
a. If you selected “int”,
enter the desired display
corresponding to high input.
(
10Vdc, 5Vdc, 20mA)
b. If you selected
“LivE”
,
apply full scale or 3/4
full scale load to sensor and enter desired
display.
Press
/MAX and
/TARE to enter the desired
display.
11.
Press MENU to store new scale factor and return
to the run mode.
12.
If the display is not zero, with no load on your
sensor, press
/TARE. Scaling is now complete.
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
.
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
Connect the Sensor Input
Depending upon sensor input type, connect your
sensors according to one of the following figures. If
your sensor type is not shown, refer to Section 3 of the
Operator’s Manual.
4 -20 mA Input with External Excitation
3-Wire dc Voltage Input with Internal Excitation
4-20 mA Transmitter with Internal Excitation
Apply Power
Plug in the meter. There is no power switch, so the
meter will be active as soon as you apply power. The
meter shows the following:
* Represents the revision code. Write this number
down. You will need this number if you call Customer
Service for assistance.
J4
1
2
3
J3
2
3
J u m p e r
U s e r
P r o v i d e d
2
3
1
2
3
J 3
J 4
E X C
S I G
C O M
J4
1
2
3
START HERE
2
3
4
Using This Quick Start Manua
l
Use this Quick Start manual with your meter to power
up, configure and scale your meter. For detailed
instructions, refer to the appropriate section in the
Operator’s Manual.
Wiring
1.
Locate the J1 connector.
2.
Insert the correct wire in each terminal as shown in
the following figure and tighten the lockdown screws.
3.
Tug gently on the wires to verify the connections.
Main Power Connections - ac
Mount the Meter
1.
Cut a hole in your panel, as shown in the figure
below.
2.
Insert the meter into the hole. Be sure the front
bezel is flush to the panel.
1.772" + .024/–.000
(45.01mm + 0.61/–0.00)
3.622" + .032/–.000
(92.00mm + 0.81/–0.00)
PANEL
Line
Neutral
AC Power
1 2
3
FUSE
Earth
Ground
J1
Configuring and Scaling Your Meter
1.
Press MENU. The meter momentarily shows
“
InP”,
then shows last saved input range.
2.
Configure the input range by pressing
/TARE
to select from the following:
4-20mA, 20-4mA, 0-5V, 1-5V and 0-10V.
3.
Press MENU to store range. The meter
momentarily shows “Stor”,
“dEc.P”,
and then
shows the last saved decimal point location.
4.
Configure the decimal point
location by pressing
/TARE to select from the
following: FFF.F, FFFF.,
FFFF, F.FFF and FF.FF.
5.
Press MENU to store decimal point. The meter
momentarily shows “
Stor”
,
“ScAL”,
and then
shows the last saved scaling method.
6.
Press
/TARE to select
“int” or
“LivE”
scaling.
“int”
is internal scaling, or
scaling without known
loads.
“LivE”
is applying
known loads to a sensor.
.
.
.
.
*
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
.
T-RST
/MAX
/TARE
MENU
RESET
.
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
T-RST
/MAX
/TARE
MENU
RESET
Warning: Do not connect AC power to your device
until you have completed all input and output
connections. This device must only be installed by a
specially trained electrician with corresponding
qualifications. Failure to follow all instructions and
warnings may result in injury!
