background image

 
 

15 

Maintenance 

6

 

MAINTENANCE 

These are the maintenance procedures required to keep the Benchtop Digital Controller in optimal 
performance. 

6.1

 

Cleaning 

Lightly dampen a soft clean cloth with a mild cleaning solution and gently clean the Benchtop Digital 
Controller. 

 

Remove all electrical connections and power before attempting any 
maintenance or cleaning. 
Do not insert any foreign objects into the Benchtop Digital Controller. 

6.2

 

Calibration 

This unit is calibrated to give optimum performance over its full operating range. Additional user 
calibration is available with adjustable gain and offset as well as ice point calibration. Refer to the 

Platinum Series User’s Manual (

M5451

) for additional information on user calibration options. 

Optional NIST traceable calibration is available. Please contact Customer Service to enquire. 

6.3

 

Fuse Specifications and Replacement 

 

Disconnect all power from source before attempting fuse replacement. 
For continued protection against the risk of fire, replace fuses with only the same size, 
type, rating and safety approvals indicated here and on the rear panel of your unit. 

 

Table 10.    Replacement Fuses 

Fuse*  Type 

F1 

0.1A 250V, 5x20mm, Fast Acting 

F2 

3.15A 250V, 5x20mm, Fast Acting 

F3 

5.0A 250V, 5x20mm, Fast Acting 

*Use only UL/CSA/VDE Approved Fuses. 

Содержание CS8DPT

















Отзывы: