background image

16

Troubleshooting

Water System

Water distribution tube

The water distribution 

tube is blocked.

Clean the water 

distribution tube.

Water line

The water quality is too 

poor. The water line is 

blocked.

Use a filter apparatus 

installed in front of the 

water inlet valve.

Silica gel tubes

The silica gel tubes 

are distorted, leads to 

blocking.

Make the silica gel tubes 

resile.

Floater valve

The floater valve 

leaks. Leads to low ice 

production.

Repair or replace.

Wheel

The icemaker is not 

properly leveled.

See installation.

ICE CUBES ARE NOT SATISFACTORY

Problem

Check part or point

Possible Cause

Probable Correction

Cubes are too small

Condenser

The condenser is dirty or 

the air grills are covered.

Clean the condenser. 

Leave space around the 

machine.

The ambient temperature The ambient temperature 

is too high.

Adjust the ambient 

temperature.

Electronic controller

The setting temperature  

is high.

See the service manual 

"adjust the size of ice 

cubes".

Refrigerant

Refrigerant leaks.

Recharge.

Cubes are too big

Electronic controller

The setting temperature 

of Electronic controller is 

low.

See the service manual 

"adjust the size of ice 

cubes".

Sensor

Temperature sensor 

of the evaporator is 

damaged.

Replace the temperature 

sensor.

The ambient and water 

temperature

The ambient temperature 

and water temperature 

are too low.

Adjust the temperature.

Содержание 37864

























Отзывы: