omal automation Rackon RK10 Скачать руководство пользователя страница 21

Страница: 21 / 31

EN -

OMAL S.p.A.

Headquarters

: Via Ponte Nuovo, 11 - 25050 Rodengo Saiano (BS) Italy •

Production Site:

Via Brognolo, 12 - 25050 Passirano (BS) Italy

Ph.

+39 030 8900145 •

Fax

+39 030 8900423 • [email protected] •

www.omal.com

Reference 8_1522 - UMAAPRK0 - 07/20

INSTRUCTION MANUAL

RACKON: RACK & PINION PART TURN PNEUMATIC ACTUATOR

RK10 - RK480

10. MAINTENANCE

OMAL actuator, if installed and used properly, does not require maintenance, as it is provided with enough lubrication for standard

long-life. During maintenance and reassembling, we recommend using, for standard version, TECNOLUBE SYNTHY POLYMER 402,

or equivalents. For low and high temperature actuators contact us.

The components for the actuator maintenance are supplied in the OMAL spare part kit (see section 9 exploded views).

OMAL declines any responsibility for the products repaired by third parties

10.1 Safety notice for maintenance

Before carrying out any type of maintenance, carefully read the safety notes in section 6

;

Before actuator disassembly operation, take pressure off, disconnect air feeding and make sure that air ports have been com-

pletely vented;

Actuator must be free of pneumatic and electric connections and must be disconnected from the valve;

Spare parts must be replaced by qualified personnel and with appropriate tools only;

In the case of Spring return actuators the springs can be under tension. Do not attempt to act manually on the actuator when

the actuator is under pressure;

In case of Spring return actuator, springs must be in FAIL position;

Do not disconnect the actuator from a line under pressure or if still under pressure;

Do not remove any component if actuator is still under pressure or installed in the line;

Do not use compressed air to remove the pistons from the actuator body;

Do not shorten the cover fixing screws, use only screws with original length, use original spare parts supplied by OMAL or by

authorized distributors;

Do not make adjustments beyond ± 5 ° on each side;

10.2 Spare parts replacing

In case your product does not meet above configurations, please look at OMAL catalogue or contact us.

Disassembly instructions

Unloose cap screws (25) crossways to remove the caps (24). If unloosing process looks too difficult, stop the operation, check

carefully if actuator is really free of air (completely vented) and/or springs are really in rest position. Cap (24) has a graved seat

where is placed a profiled gasket (23). Check gasket and graved seat.

Double Acting

Spring Return Fail Close

Spring Return Fail Open

Содержание Rackon RK10
































Результаты поиска

Содержание Rackon RK10

Отзывы:

Бренды по названию

Популярные бренды

omal automation Rackon RK10, Инструкция по эксплуатации

Результаты поиска

Содержание Rackon RK10

Отзывы:

Бренды по названию

Популярные бренды