manualshive.com logo in svg

omal automation Rackon RK10, Инструкция по эксплуатации

Поделиться
Скачать
omal automation Rackon RK10 Скачать руководство пользователя страница 11

EN - 

11

OMAL S.p.A.

Headquarters

: Via Ponte Nuovo, 11 - 25050 Rodengo Saiano (BS) Italy  •  

Production Site:

 Via Brognolo, 12 - 25050 Passirano (BS) Italy

Ph.

 +39 030 8900145  •  

Fax

 +39 030 8900423  •  [email protected]  •  

www.omal.com

Reference 8_1522 - UMAAPRK0 - 07/20

IT

EN

DE

FR

ES

INSTRUCTION MANUAL

RACKON: RACK & PINION PART TURN PNEUMATIC ACTUATOR

RK10 - RK480

7.1.2 Plate installation

If a direct installation is not possible because of discrepancy between actuators and valve flanges or because of power transmis-

sion differences, is it possible to use plates. Adapting plates make the installation easier and offer more space for actuator/valve 

installation.

7.1 Valve/Actuator installation

7.1.1 Direct installation

Direct installation is the best solution to avoid play or clearance between valve and shaft. Direct installation needs same flanged 

standard connection on valve and actuator as well as same dimension of valve stem and actuator socket.

Installation:

A

. Pull reduction in valve stem (in case of reduction needs only);

B

. Put valve stem into the actuator socket;

C

. Verify correct connection to avoid play, clearance or interferences in between;

D

. Place screws (1) and relevant washers (2) and screw them in compliance with below torque 

indications;

E

. After installation, check actuator rotation direction for Double acting (DA) actuators;

F

. After installation, check actuator rotation direction and home position in case of Spring Return (SR);

G

. In case of discrepancy contact us;

Installation:

A

. Place plate (3) on valve flange;

B

. Pull reduction in valve steam (in case of reduction needs only);

C

. Put valve stem into the actuator socket;

D

. Verify correct connection to avoid play, clearance or interferences in between;

E

. Place screws (1) and relevant washers (2) and screw them in compliance with below torque 

indications;

F

. After installation, check actuator rotation direction for Double acting (DA) actuators;

G

. After installation, check actuator rotation direction and home position in case of Spring Return (SR);

H

. In case of discrepancy contact us;

Содержание Rackon RK10
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды