manualshive.com logo in svg

Olympus TRPP 5810, Руководство пользователя

Поделиться
Скачать
Olympus TRPP 5810 Скачать руководство пользователя страница 14

DMTA-20070-01EN, Rev. A, October 2014

Important Information — Please Read Before Use

 

8

In order to prevent human injury and/or equipment damage, do not disassemble, 
modify, or attempt to repair the instrument.

Safety Symbols

The following safety symbol might appear on the instrument and in the instruction 
manual:

 General warning symbol

This symbol is used to alert the user to potential hazards. All safety messages that 
follow this symbol shall be obeyed to avoid possible harm or material damage.

Safety Signal Words

The following safety symbols might appear in the documentation of the instrument:

The DANGER signal word indicates an imminently hazardous situation. It calls 
attention to a procedure, practice, or the like, which, if not correctly performed or 
adhered to, will result in death or serious personal injury. Do not proceed beyond a 
DANGER signal word until the indicated conditions are fully understood and met.

The WARNING signal word indicates a potentially hazardous situation. It calls 
attention to a procedure, practice, or the like, which, if not correctly performed or 
adhered to, could result in death or serious personal injury. Do not proceed beyond a 
WARNING signal word until the indicated conditions are fully understood and met.

CAUTION

DANGER

WARNING

Содержание TRPP 5810













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды