Olympus SZX-RFL3 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 22

Olympus SZX-RFL3 Скачать руководство пользователя страница 5

3

1

MODULE NOMENCLATURE

}If you have not assembled the microscope system, please see Chapter 4, “ASSEMBLY”.

*

1

Fluorescence Illuminator

SZX-RFA3

*

3

Lamp housing

U-LH100HGAPO
U-LH100HG

Power supply unit (for 100 W mercury burner)

*1. The SZX-RFA3 fluorescence illuminator is composed of; @ filter changer; ² microscope body mount; ³ pillar adapter; |

lighting head.

*2. · When using the DFPLAPO1XPF objective, set the magnification at 10X to maximum as indicated on the zooming knob.

If the magnification under 10X is selected, vignetting will occur.

· The DFPLAPO1X-2 objective should be used when using the SZX-ZB9 microscope body. Note that, however, the light

brightness may reduce in this case.

*3. A lamp housing designed for the U-ULH mercury burner can also be used.
*4. A transparent lighting base will be effective in screening for sorting manifested items.

*

2

SZX Zoom Microscope Body
SZX-ZB12

*

2

Objective
DFPLAPO1.2XPF
DFPLAPO1XPF

*

4

Base

@

|

²

³

«
...
3
4
5
6
7
...
»

Содержание SZX-RFL3























Отзывы:

Нет отзывов