Olympus SZX-RFL3 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

Olympus SZX-RFL3 Скачать руководство пользователя страница 10

SZX–RFL3

8

The following diagram shows how to install the modules, and the numbers indicate the sequence of installation. The items
enclosed in are detailed on the subsequent pages.

* To prevent you from forgetting to mount ne of both of the specified excitation and barrier filters, they must always be attached

together along a single line.

** It is easier to insert the ND filter before mounting the filter changer.

# Remove dirt and dust from each part before assembly, and assembly the parts carefully by following the numbers

shown in the figure.

ASSEMBLY

}Please have your local Olympus representative perform the assembly work.

4-1 Assembly Diagram

Eyepiece

Observation tube

Excitation filter
slider*

Filter changer

Barrier filter slider*

Zoom microscope body

Coupling

Focusing block

Objective

Body mount

Pillar

Power supply unit
(for 100 W mercury burner)

Pillar
adapter

Base

Lighting head

Shielding plate

Stage plate

Black plate

Glass plate

Fluorescence
stage plate set

Lamp housing
U-LH100HGAPO
U-LH100HG

Specimen
holder

· Allen screwdriver

(Provided with the SZX

microscope body.)

· Allen wrench*

(Provided with the base.)

· Allen wrench (small)

(Provide with the SZX-RFL3.)

Tools Used

* Do not use this Allen wrench for a pur-

pose other than installing the pillar adapter.
If the Allen wrench is used for a part other
than that described above, the force with
which it is applied may break the part.

ND filter**

«
...
8
9
10
11
12
...
»

Содержание SZX-RFL3























Отзывы:

Нет отзывов