Olympus PT-022 Скачать руководство пользователя | Manualshive

Страница: 7 / 43

background image

E-6

●

Do not perform operations other than specified in this instruction
manual, do not remove or modify parts other than specified, and do
not use parts other than specified.
Any troubles in taking pictures or with the equipment resulting from
the above actions shall be outside the guarantee.

●

OLYMPUS CORPORATION shall be in no way responsible for
accidents involving immersion of a digital camera in water.

●

OLYMPUS CORPORATION shall not pay any compensation for
accidents (injury or material damage) at the time of use.

●

When the enclosure of the balance weight breaks, the metal on the
inside may corrode. Take care not to damage the enclosure.

●

After use, wash the balance weight with pure water and wipe off all
moisture sufficiently.

●

Do not use the following chemicals for cleaning, corrosion
prevention, prevention of fogging, repair or other purposes. When
these are used for the Case directly or indirectly (with the
chemicals in vaporized state), they may cause cracking under high
pressure or other problems.

Chemicals which cannot be used Explanation

Volatile organic solvents,
chemical detergents

Do not clean the Case with alcohol, gasoline, thinner
or other volatile organic solvents or with chemical
detergents etc. Pure water or lukewarm water is
sufficient.

Anticorrosion agent

Do not use anticorrosion agents. The metal parts use
stainless steel or brass, and washing with pure water
is sufficient.

Commercial defogging
agents

Do not use commercial defogging agents. Always
use the specified desiccant silica gel.

Grease other than specified
silicone grease

Use only the specified silicone grease for the silicone
O-ring, as otherwise the O-ring surface may
deteriorate and water leakage may be caused.

Adhesive

Do not use adhesive for repairs or other purposes.
When repair is required, please contact a dealer or a
service station of OLYMPUS CORPORATION.

PT̲022̲E.qxd 2004.3.18 4:34 PM ページE-6

«
...
5
6
7
8
9
...
»

Содержание PT-022












































Отзывы:

Нет отзывов

Похожие инструкции для PT-022

Бренд: Gates Страницы: 26

Бренд: Kabuto Страницы: 25

DWSC - Vintage C

Бренд: Daikin Страницы: 57

Бренд: e-Line Technology Страницы: 36

Бренд: M-S Cash Drawer Страницы: 2

Бренд: M-Audio Страницы: 61

Бренд: Vaisala Страницы: 24

Бренд: Yakima Страницы: 4

Outdoor Motion Sensor PMS03

Бренд: X10 Страницы: 2

Бренд: Hama Страницы: 56

Бренд: Omron Страницы: 8

Бренд: ACERBIS Страницы: 72

Бренд: Deka Страницы: 4

BIS M-411-068-001-09-S72

Бренд: Balluff Страницы: 2

Бренд: Kodak Страницы: 2

Бренд: AC Schnitzer Страницы: 20

Бренд: IFM Electronic Страницы: 37

Бренд: SIXTOL Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды