background image

EN 21

EN

6

In the event that you discover that water has leaked into the product, 
stop using the camera underwater immediately, remove any moisture 
adhered to the product, remove the camera and lens from the Case, 
and consult a service center.

7

Please remove the O-ring when traveling by air. Otherwise air 
pressure may make it impossible to remove the rear cap.

8

To ensure safe use of the product, carefully read the instruction 
manuals of the camera and the Case to which the product is attached.

9

When attaching this product to the Case, make sure that foreign matter 
is not trapped between the O-ring and the contact surface as this can 
adversely affect the waterproofing and result in leakage occurring.

0

When attaching this product to the Case, be sure to follow the 
attachment method set out in this manual, ensuring that the 
instructions are followed in the correct order.

a

Before detaching this product from the Case, dry all parts fully and 
check that no moisture is adhered.

b

When storing this product, always detach it from the Case and fit the 
front cover and the rear cap.

c

When the Lens Port is not to be used for a long time, remove the O-
ring from the groove to prevent deformation of the O-ring, apply a thin 
coat of silicone grease, and store it in a clean plastic bag or the like.

Chemicals which cannot 

be used

Explanation

Volatile organic solvents,
chemical detergents

Do not clean the Lens Port with alcohol, gasoline, 
thinner or other volatile organic solvents or with 
chemical detergents etc. Use pure water or 
lukewarm water.

Anticorrosion agent

Do not use anticorrosion agents. Wash with pure 
water.

Commercial defogging 
agents

Do not use commercial defogging agents. Always 
use the specified desiccant silica gel.

Grease other than 
specified silicone grease

Use only the specified silicone grease for the 
O-ring, as otherwise the O-ring surface may 
deteriorate and water leakage may occur. 

Adhesive

Do not use adhesive for repairs or other purposes. 
When repair is required, please contact a dealer or 
a service station of OLYMPUS CORPORATION.

PPO-EP02_EN.book  Page 21  Tuesday, March 24, 2015  10:08 AM

Содержание PPO-EP02


















Отзывы: