1
2
1
Pictogram Installation
3
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
ΑΤΤΕΝΤΙΟΝ!!!
When the luminaire is used without the pictograms
or the SP-1100 and you require more light output
then remove the lens that covers the LEDs.
Lens Removal
Remove the diffusor and then by pressing the test
button briefly an operation test is initiated. The light
source and the emergency circuit of the device are
tested. The manual test can be conducted only if the
mains power supply and the battery are connected.
During this test period the LAMP TEST LED will blink.
The battery must have adequate charge. This test
lasts for 3 seconds.
Manual Operational Test
2. Always use in any case round mains cable, with a
diameter of 5-10mm (H05RN-F type 2x1mm² or
any other type, at least equal to it’s mechanical
and electrical properties). ATTENTION!! The cable
o
These luminaires are used indoors (ta 40 C) where
emergency light is needed. Each luminaire must be
permanently connected to mains power supply. In
normal operation the led strip lights and the battery
is charging. In case of a mains power supply
failure the luminaire will light the led strip
automatically in emergency mode. When the mains
power supply is restored the device turns to
normal operation.
CN5:
LED connector
CN4:
LED connector
CN3:
Battery connector
CN1:
Maintained, Non maintained selection
KL1:
Power connector
Connectors
6.
I
s not allowed to discard batteries into
t i
common trash bins, they must be discarded
only
in battery recycling points. Do not
incinerate.
5. In case of inactive use for a period greater than 2
months, disconnect the battery by pulling out the
battery’s connector.
3. The device must be connected to the mains
power supply through a circuit breaker that is
depends on the total line’s power load.
4. In case of battery replacement, it must be
replaced by the same type, by the manufacturer
or a competent person.
must not be deformed in any way (This
requirement is important to ensure the ΙΡ rating).
General
Commissioning
—
During commissioning of the luminaire write the commissioning date on the battery.
—
A full duration test should be conducted after 24 hours of continuous charging. The test is initiated by isolating
the mains power supply. Verify that the LED lamp is lit during the test period for at least the stated duration.
—
When power is applied to the unit inspect that the CHARGE indicator is steady, and that the led lamp is lit
(maintained operation) or OFF (non-maintained operation)
—
After installation, a 24 hours charging cycle must be completed, in order to achieve the nominal autonomy.
2
5
6
Ν
for neutral and
L
for live wire.
Installation Instructions
3
4
2
2
1
1
Power Connections
7
9
11
8
10
12
Install the included tie (if needed) to fasten
securely the power cables.
Battery Connection
This unit has replaceable batteries that can be replaced or changed by the manufacturer or a competent person.
1
1
1
1
Luminaire
Set of Pictograms
Mounting accessories
Manual
Package Contents
4. Replace the removed parts (previous steps 1 and 2).
3. Remove the old battery and place a new one of the same type and characteristics.
2. Follow step 2 of the installation instructions and remove the reflector.
1. Follow step 1 of the installation instructions and remove the diffusor.
It can be done only by a competent person and after the mains interruption
.
Battery Replacement
923500000_09_003
923500000_09_003
923500000_09_003
Non maintained
operation
Maintained
operation
Description
Indications LED Status
CHARGE
(green)
Charging
Emergency mode or
battery disconnected
Note:
Permanently
ON
Off
N
L
A
B
A
A
A
A
A
A
Attention!!
The 6 plastic latches (A)
must be secured (click sound). This
requirement is important to ensure
the IP42 rating. Power on the
luminary.
Mounting Methods
Oly luminaires can be surface mounted on walls or ceilings. For these mounted installations, special
accessories are included.
Wall
bottom
view
Wall installation
Ceiling installation
Ceiling
* ATTENTION!!! The below mounting methods can be done after request of the necessary
mounting accessories!!
Extra Mounting Methods *
Suspended ceiling installation
with mounting accessory
A-3018
Suspended installation with A-3018 accessory
The luminary can be installed in a suspended
ceiling.
A marking panel (
SP-1100
) can be installed on the luminary pointing the desired direction.
Suspended ceiling installation
with mounting accessories
and marking panel
Ceiling installation
with marking panel
Install the included rubber gasket and pass through the
power cables.
1. Fit the pictogram you need to the diffuser, be careful to
secure it on the 3 plastic holders.
2. Refit the diffusor with the pictogram.