MENU). The factory default for this
temperature is 18.0ºC. To deactivate night
mode press and hold the key for more
that 3". The symbol will be replaced by
the symbol .
4 . S E L E C T I N G A R E A
PRESENCE/ABSENCE
(the thermostat is
in the ON state).
This option can be activated if we press and
hold the key for more that 3". The
backlight will be lit and the symbol will be
shown on the top left of the screen while the
internal relay will send the command to the
burner. The command will be active
depending on the time that has been
adjusted in the MENU option
(Boiler time), or until the key is
pressed again. By default, if the boiler time
is set to 00 so the deactivation can only be
done by the key. The Boiler command is
independent from other thermostat
functions and can even be issued with the
thermostat deactivated (OFF state). The
default boiler time is 30 minutes.
3. SELECTING BOILER ACTIVATION
(only for BS-813/A).
In normal operation the symbol , shows
the presence of a person in the room and all
the selected programs are performed
normally. For limited absence from the area
(from a few hours to a few days) there is a
capability t o activate the absence program.
If the key is pressed for more than 3"
then the backlight is activated for 2" and the
symbol will be replaced by the
symbol . The selection overrides any
o t h e r p r o g r a m . T h e p r e s e l e c t e d
temperature can be shown on the screen
by pressing one of the keys and
can not be altered. This temperature can be
changed only via the option (Absent
time in the MENU). The factory default
value is 16.0 ºC and can be adjusted from
6.0 to 30.0 ºC. To deactivate the absence
command press and hold the key for
more than 3", the thermostat will continue
with the program that was running before
the absence command was issued.
GENERAL
When the plastic battery separator found
between the two batteries is removed then
the device is activated and all the symbols
are shown on the LCD for 1", immediately
follows a number that corresponds to the
firmware version and then the initial screen.
In the middle of the screen we can see the
current temperature. The clock shows
00:00, the date is 1st January (Friday)
2016 and the thermostat is inactive (OFF
state). In this state the only available
options are the activation or deactivation of
the boiler (only on BS-813/A) and the entry
t o t h e s e t t i n g s m e n u . I f t h e
button is pressed momentarily the
backlight will light for 2" and the symbols
, and
ΜΑΝ
which are the factory default.
1. ENTERING THE MENU
(the thermostat
is in the OFF state
).
(the thermostat is ON and in manual
operation).
If the key is pressed for more that 3"
then the indication is deactivated and the
indication is shown which means that
night mode has been selected. This
selection temporarily replaces the manual
temperature setting with the night program
setting for as long as it is active. If any of the
keys is pressed then the screen
will show the selected temperature for the
night program (it can be adjusted only
through the setting (night) in the
To enter the menu of the thermostat that
contains the setting you must press for
more that 3".
The screen will be lit and it will remain in this
state during the programming of the
settings. It must be stressed the only
blinking indications can be adjusted. To
navigate through the settings use the
keys while using the keys
to change the values. With the key
select the value that will be changed and
with the key we can return to the
previous state. If no key is pressed for more
that 2 minute then the device exits the
programming mode and stores all the
settings.
2. SELECTING DAY OR NIGHT MODE
MENU
ENTER
MENU
ENTER
ESC
ESC
ESC
Page 2 from 10
940812001_09_001
