manualshive.com logo in svg

OLT SunShed Garden Shed SSGS1212-AK-METAL, Инструкция по сборке

Садовый сарай OLT SunShed SSGS1212-AK-METAL - это идеальное решение для хранения садового инвентаря и инструментов. Сборка легка и быстрая благодаря подробной сборочной инструкции. Скачайте бесплатное руководство по сборке на manualshive.com и начните наслаждаться вашим новым сарайчиком прямо сейчас!

Поделиться
Скачать
background image

25.

 Position and attach the Door Header to Door Jamb and Narrow Wall Panel top framing. Header 

should sit flush with Door Jamb and Outside of Narrow Wall Siding.  Attach with 

4 - 2 1/2” screws

.

Dado cut on edge to 
top and outside.

Advice:

 Prior to fastening walls and installing 

rafters, take time to confirm your walls are 
level, square and plumb.  
 
Measure diagonal at top and bottom of walls 
corner-to-corner. This should be approximately 
189 3/8”. More importantly, if measurements 
are not within 1/4”, your walls are not square. 
Adjusting now will make it easier to the roof 
section later

.

189 3/8”

189 3/8”

24. 

Locate Vertical Door Jamb and position flush against right wall panel stud. The Jamb is 3” wide 

and will sit flush to outside of wall siding.  When positioned correctly, secure Jamb using 

4 - 2 1/2” 

screws

.  

Jamb sits flush 
with Wall framing

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 15

Содержание SunShed Garden Shed SSGS1212-AK-METAL














































Отзывы:

Нет отзывов

Похожие инструкции для SunShed Garden Shed SSGS1212-AK-METAL

Palmako Claire 2 Installation Manual preview
Claire 2
Бренд: Palmako Страницы: 38
Coco Village GARDEN PLAYHOUSE 79991102270 Assembly Instructions Manual preview
GARDEN PLAYHOUSE 79991102270
Бренд: Coco Village Страницы: 8
Palmako 420880 Installation Manual preview
420880
Бренд: Palmako Страницы: 55
Palmako 109408 Assembly, Installation And Maintenance Manual preview
109408
Бренд: Palmako Страницы: 53
Palmako 103761 Installation Manual preview
103761
Бренд: Palmako Страницы: 62
Lemeks Palmako FRF28-3829 Installation Manual preview
Palmako FRF28-3829
Бренд: Lemeks Страницы: 62
Lemeks Palmako FRBC44-5540 Installation Manual preview
Palmako FRBC44-5540
Бренд: Lemeks Страницы: 63
Lemeks Palmako FRB28-3232-3 Installation Manual preview
Palmako FRB28-3232-3
Бренд: Lemeks Страницы: 52
Lemeks Palmako Ella FRB28-2632 Installation Manual preview
Palmako Ella FRB28-2632
Бренд: Lemeks Страницы: 92
Lemeks PALMAKO ANDRE EL18-4555-3 Assembly, Installation And Maintenance Manual preview
PALMAKO ANDRE EL18-4555-3
Бренд: Lemeks Страницы: 60
Lemeks BNVPI 109640 Assembly, Installation And Maintenance Manual preview
BNVPI 109640
Бренд: Lemeks Страницы: 154
Mr. GARDENER FRJ70-4747 Installation Manual preview
FRJ70-4747
Бренд: Mr. GARDENER Страницы: 63
Dancover SkyLight Shed Manual preview
SkyLight Shed
Бренд: Dancover Страницы: 66
HAMPTON BAY 5LGZ1291-V3 Use And Care Manual preview
5LGZ1291-V3
Бренд: HAMPTON BAY Страницы: 8
Karibu SEEFELD 5 Assembly Instructions Manual preview
SEEFELD 5
Бренд: Karibu Страницы: 42
Palmako FR28-3227 Installation Manual preview
FR28-3227
Бренд: Palmako Страницы: 70
Palmako FR70-5353 Installation Manual preview
FR70-5353
Бренд: Palmako Страницы: 129
Mercia Garden Products 03DTSHAX0705HGD2MW-V1 Instructions Manual preview
03DTSHAX0705HGD2MW-V1
Бренд: Mercia Garden Products Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды