OLT SSGS812 Скачать руководство пользователя страница 11

Страница: 11 / 42

Optional:

Caulking seams will help

prevent moisture from entering your shed.
Caulking is included to complete Polygal
Windows only. Additional Caulking may be
required.

14.

Starting at the Rear Left Side, position

Solid Wall Panel

on top of plywood floor.

The Wall Panel bottom framing will sit flush
with floor framing. Wall siding will overhang
the floor.

Important:

Make sure all walls are aligned

in their upright position. If not, water may
leak into your shed. Unsure if panel is facing
up or down? check siding on window wall
panel to match alignment, or keep track of
your recently attached bottom plates.

15.

The side panels will sit flush with floor

framing in the corners, with the rear panels
sandwiched between them.

Note:

Siding will

overhang the floor by approx. 1/2”.

Outside 2x3
framing of wall
panel is flush
with outside of
floor
framing when
properly
aligned.

Left Side Wall Panel

Rear of Shed

Bottom Wall Plate

13.

Starting with

Solid Wall Panels

, carefully lay panel face down. Position and attach

Wall Plate

(1 1/2” x 2 1/2” x 45 1/2”) to bottom of studs of each wall panel with 3 - 2 1/2” screws. Position so plates
are flush with framing.

Left Side

Front

Important:

Pilot hole

ALL

2x3 Wall Studs

with 1/8” drill bit prior to screwing.

This will make it much easier to

attached together.

Pilot

Hole Plate

first.

Do Not Attach Walls To
Floor until Step 29.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 11

Содержание SSGS812











































Результаты поиска

Содержание SSGS812

Отзывы:

Похожие инструкции для SSGS812

Бренды по названию

Популярные бренды

OLT SSGS812, Инструкция по сборке

Результаты поиска

Содержание SSGS812

Отзывы:

Похожие инструкции для SSGS812

Бренды по названию

Популярные бренды