manualshive.com logo in svg

OLT 6x6 Apex, Инструкция по сборке

Поделиться
Скачать
OLT 6x6 Apex Скачать руководство пользователя страница 15

30. 

Temporarily attach gable walls to top plate with 

2 - 2” screws (Part E). 

Screw from the bottom

of gable framing down into top plate. Gables may need slight adjustment in 

Step 40 

and then be 

completely attached with an additional 

6 - 2” screws (Part E).

Position 2nd Gable on side walls.

29.

Locate and place 

Gable Wall (Part 2H)

so gable framing sits flush with the inside of the top plate.

Center from front to rear using a Straight Edge to confirm angle of gable frame and Top Plate line up.
Adjust gable accordingly. From the outside, make sure gable flashing overhangs wall siding.

Gable Frame

Straight Edge

Gable Flashing

31. 

Position and temporarily attach 2nd Gable as per 

Steps 28-29.

Wall Framing

Gable Wall

Temporarily attach gable walls to top plate.
Slight adjustment may be required later

1-888-658-1658                        www.outdoorlivingtoday.com            [email protected]

Page 15

Содержание 6x6 Apex
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды