Olivetti d-Color MF2613En Скачать руководство пользователя страница 69

Страница: 69 / 375

2PV/2PW

1-3-31

U251

Checking/clearing the maintenance count

Description

Displays, clears and changes the maintenance count.

Purpose

To check the maintenance count.

Also to clear the count during maintenance service (replacing the maintenance kit).

Method

1. Press the start key. The maintenance count is displayed.

Setting

1. Select [M.Cnt A] using the cursor up/down keys.
2. Change the setting using the cursor left/right keys or numeric keys.

3. Press the start key. The count is set.

Clearing

1. Select [Clear] using the cursor up/down keys.
2. Press the start key. The count is cleared.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Setting range

Initial setting

Maintenance count

0 to 9999999

Service Manual

Y116650-5

Содержание d-Color MF2613En























































































































































































































































































































































































Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды

Olivetti d-Color MF2613En, Руководство по обслуживанию

Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды