Olivetti d-Color MF2613En Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 375

background image

2PV/2PW

1-4-23

6400

Zero-cross signal error

The zero-cross signal does
not reach the engine PWB for
more than 1 s.

Defective connec-
tor cable or poor
contact in the con-
nector.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Power source PWB (YC103) and relay PWB
(YC1)
Relay PWB (YC4) and engine PWB (YC9)

Defective power
source PWB or
engine PWB.

Replace the power source PWB or the
engine PWB and check for correct operation
(see page 1-5-29, 1-5-27).

7001

Toner motor K error

When the toner motor K is
driven, the motor over-current
detection signal is detected
continuously for 50 times (5 s)
at 100 ms intervals.

Defective connec-
tor cable or poor
contact in the con-
nector.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Toner motor K and engine PWB (YC23)

Defective drive
transmission sys-
tem of the toner
motor K.

Check if the rollers and gears rotate
smoothly. If not, grease the bushes and
gears. Check for broken gears and replace if
any.

Defective toner
motor K.

Replace the toner motor K.

Defective engine
PWB.

Replace the engine PWB and check for cor-
rect operation (see page 1-5-27).

7002

Toner motor C error

When the toner motor C is
driven, the motor over-current
detection signal is detected
continuously for 50 times (5 s)
at 100 ms intervals.

Defective connec-
tor cable or poor
contact in the con-
nector.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Toner motor C and engine PWB (YC25)

Defective drive
transmission sys-
tem of the toner
motor C.

Check if the rollers and gears rotate
smoothly. If not, grease the bushes and
gears. Check for broken gears and replace if
any.

Defective toner
motor C.

Replace the toner motor C.

Defective engine
PWB.

Replace the engine PWB and check for cor-
rect operation (see page 1-5-27).

7003

Toner motor M error

When the toner motor M is
driven, the motor over-current
detection signal is detected
continuously for 50 times (5 s)
at 100 ms intervals.

Defective connec-
tor cable or poor
contact in the con-
nector.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Toner motor M and engine PWB (YC24)

Defective drive
transmission sys-
tem of the toner
motor M.

Check if the rollers and gears rotate
smoothly. If not, grease the bushes and
gears. Check for broken gears and replace if
any.

Defective toner
motor M.

Replace the toner motor M.

Defective engine
PWB.

Replace the engine PWB and check for cor-
rect operation (see page 1-5-27).

Code

Contents

Causes

Check procedures/

corrective measures

Service Manual

Y116650-5

«
...
157
158
159
160
161
...
»

Содержание d-Color MF2613En
























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Color MF2613En

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды