Oliver 4045 Скачать руководство пользователя страница 15

.  

 

Troubleshooting 

 

Description of Symptoms 

Possible Cause 

Corrective Action 

Machine will not start 

1.  Fuse blown or circuit breaker 

tripped 

2. Cord 

Damaged 

3. Faulty 

switch 

4.  Not connected to power 

source 

5.  Connected to wrong voltage 

6.  Key in the “OFF” position 

7.  Emergency stop button 

pressed 

1.  Replace fuse or reset circuit 

breaker 

2.  Have cord replaced 

3. Replace 

switch 

4. Check 

connection 

5. Check 

voltage 

6.  Insert key and turn to “ON” 

position 

7.  Rotate emergency stop button 

clockwise until it pops out 

Blade does not come up to speed 

1.  Cable too light or too long 

2. Low 

current 

3.  Motor not wired for correct 

voltage 

1.  Replace with adequate size 

cable 

2.  Contact local electric 

company 

3.  Refer to motor nameplate for 

correct voltage 

Does not make accurate 45° or 
90° cuts 

1.  Stops not adjusted correctly 

2.  Angle pointer not set 

accurately 

3.  Miter gauge out of adjustment 

1.  Check blade with combination 

square and adjust stops 

2.  Check blade with combination 

square and adjust pointer 

3.  Adjust miter gauge 

Saw makes unsatisfactory cuts 

1. Dull 

blade 

2.  Blade mounted backwards 

3.  Gum or pitch on blade 

4.  Incorrect blade for cut 

1.  Sharpen or replace blade 

2.  Turn blade around 

3.  Remove blade and clean 

4.  Change blade to correct type 

Material binds blade when ripping 

1.  Fence not aligned with blade 

2. Warped 

wood 

3.  Excessive feed rate 

4.  Splitter not aligned with blade 

1.  Check and adjust fence 

2.  Select another piece of wood 

3.  Reduce feed rate 

4.  Align splitter with blade 

 

15

Содержание 4045

















Отзывы: