background image

  

WARNING

Read this manual completely and observe all warning labels on the machine.  Oliver Machinery has made 
every attempt to provide a safe, reliable, easy-to-use piece of machinery.  Safety, however, is ultimately 
the responsibility of the individual machine operator.  As with any piece of machinery, the operator must 
exercise caution, patience, and common sense to safely run the machine.  Before operating this product, 
become familiar with the safety rules in the following sections.

Always keep guards in place and in proper operating condition.

Use blade guard for every applicable operation including all through cuts.  If guard is removed 
for special non-through cuts such as dado and rabbet cuts, replace before further use of the 
saw.

Keep hands out of line with the saw blade.

Use a push stick.

Do not perform any operation freehand.

Never reach around or over the saw blade.

1.

If you are not properly trained

 in the use of a tablesaw do not use until the proper training has been 

obtained.

2.

Read, understand and follow 

the safety instructions found in this manual.  Know the limitations and 

hazards associated with this machine.

3.

Electrical grounding:  

Make certain that the machine frame is electrically grounded and that a 

ground lead is included in the incoming electrical service.  In cases where a cord and plug are used, 
make certain that the grounding plug connects to a suitable ground.  Follow the grounding procedure 
indicated in the National Electrical Code.

4.

Eye safety:  

Wear an approved safety shield, goggles, or glasses to protect eyes.  Common 

eyeglasses are only impact-resistant, they are not safety glasses.

5.

Personal protection:  

Before operating the machine, remove tie, rings, watch and other jewelry and 

roll up sleeves above the elbows.  Remove all loose outer clothing and confine long hair.  Protective 
type footwear should be used.  Where the noise exceeds the level of exposure allowed in Section 
1910.95 of the OSHA Regulations, use hearing protective devices.  Do not wear gloves.

6.

Guards:  

Keep the machine guards in place for every operation for which they can be used.  If any 

guards are removed for maintenance, DO NOT OPERATE the machine until the guards are 
reinstalled.  

7.

Work area:  

Keep the floor around the machine clean and free of scrap material, saw dust, oil and 

other liquids to minimize the danger of tripping or slipping.  Be sure the table is free of all scrap, 
foreign material and tools before starting to use the machine.  Make certain the work area is well 
lighted and that a proper exhaust system is used to minimize dust.  Use anti-skid floor strips on the 
floor area where the operator normally stands and mark off machine work area.  Provide adequate 
work space around the machine.

8.

Material condition:  

Do not attempt to saw boards with loose knots or with nails or other foreign 

material.  Do not attempt to saw twisted, warped, bowed stock.

9.

Operator position:  

Maintain a balanced stance and keep your body under control at all times.

10.

Before starting:  

Before turning on machine, remove all extra equipment such as keys, wrenches, 

scraps, and cleaning rags away from the machine.

3

Содержание 4035

























Отзывы: